Mn + 1AXn (MAX; n = 1–3) phases are ternary layered nitride and carbide compounds featuring a combination of metallic and ceramic properties. Highly basal-plane textured and polycrystalline Cr2AlC, Ti2AlC, and Ti3AlC2 single-phase coatings have been synthesized on both amorphous and polycrystalline substrates via controlled thermal annealing of magnetron-sputtered nanoscale multilayers built by individual transition metal, carbon, and aluminum layers. Formation of substitutional solid solution carbide phases was triggered via solid-state diffusion reactions during annealing. Lower ordered Ti2AlC initially crystallized at an intermediate temperature range and was recognized as an intermediate reactant in the case of synthesizing the Ti3AlC2 312 MAX phase via annealing corresponding stoichiometric multilayers. The crystallization onset temperatures identified via in-situ high-temperature x-ray diffraction measurements were approximately 480, 660, and 820 °C for Cr2AlC, Ti2AlC, and Ti3AlC2, respectively. Contrary to the usually observed columnar structure representative of magnetron-sputtered coatings, the coatings synthesized via the current approach are composed of plateletlike, elongated crystallites. The nanoscale multilayered design stimulates the textured growth of MAX structures during thermal annealing. More specifically, the preferred crystallographic orientation relationships among the as-deposited transition metal layers, the intermediate solid solution phases, and the end-product MAX phases facilitate the growth of textured MAX phase films.
Friction and wear performance of non-reactively magnetron-sputtered hydrogen-free TiC/a-C coatings were characterized under lubricated oscillating sliding conditions against 100Cr6 steel. The friction mediators, isooctane, ethanol and distilled water, were chosen to address the actual trend of environmentally friendly green technologies in mobility and the potential use of carbon-based nanocomposite thin film materials for tribocomponents in contact with gasoline and alternative biofuels. Sliding pairs of the TiC/a-C coatings showed significantly reduced friction and wear compared to the reference materials under both unlubricated and lubricated conditions (when using the aforementioned media isooctane, ethanol and distilled water). Quasi-stationary friction coefficient of the TiC/a-C sliding pairs after running-in was almost independent of test conditions and could be traced back to self-lubrication as a result of the formation of a transfer layer on the steel counter body. Wear of the coatings based on micro-abrasion and tribochemical reaction was significantly influenced by the environmental conditions. Lowest wear was measured after tests in non-polar isooctane whereas highest wear was measured after tests in water.
Elemental Cr/C/Al multilayers (stoichiometric ratio: 2:1:1) with and without a Cr overlayer have been synthesized on Zircaloy-4 substrates by magnetron sputtering. The effects of annealing temperatures (400 and 550 °C) on phase/microstructure formation, mechanical properties, and oxidation/corrosion performance have been comparatively studied. Annealing of the multilayers at 400 °C led to the formation of nanocrystalline composite consisting of intermetallic and binary carbide phases. Single-phase Cr2AlC was obtained after 550 °C annealing, but with microcracking of the coatings. Both annealed coatings displayed similar mechanical properties, high-temperature oxidation, and hydrothermal corrosion mechanisms. The composite coatings annealed at 400 °C significantly enhance the high-temperature oxidation resistance (α-Al2O3 scale growth) and hydrothermal corrosion (Cr2O3 passivation layer formation) of a Zircaloy-4 substrate without coating microcracking and delamination. Nanocomposite CrCAl-based coatings are promising candidates for coated ATF applications with acceptable processing temperatures and excellent oxidation/corrosion resistances for a zirconium alloy substrate.
In this study, we report on phase formation and microstructure evolution in multiscale magnetron sputtered Ru/Al multilayers upon thermal annealing in vacuum at slow heating rates of 10 K/min. By specifically adjusting the microstructure and design of the as-deposited multilayers, the formation of certain desired phases can be tuned. We demonstrate that the synthesis of single phase RuAl thin films is possible in a very controlled manner in a solid state only via thermal activation without initiating the self-propagating exothermic reactions of Ru/Al multilayers. To investigate phase formation sequences and the resulting microstructures, Ru/Al multilayers were designed via magnetron sputtering with systematic variation of bilayer modulation periods and subsequent vacuum annealing. Thin films samples were characterized by in situ high-temperature XRD, TEM imaging and diffraction. It is shown that different phase sequences appear in strong correlation with the modulation length. Depending on the multilayer design, the phase formation toward single-phase RuAl thin films happens as either a multi-step or single-step event. In particular, below a critical threshold of the modulation period, the multi-step phase formation can be suppressed, and only the desired RuAl target phase is obtained with a pronounced growth in a preferred orientation. This finding may be versatile for the targeted synthesis of intermetallic phases, contributing to further understanding of phase formation in such nanoscale multilayer systems.
A comprehensive comparison of results obtained by finite element modelling (FEM) and plasma diagnostics between direct current (d.c.) and radio frequency (RF) magnetron sputtering at a frequency of 13.56 MHz is presented. This research studies the influence of power in the range 20 W to 90 W at a constant argon gas pressure of 1 Pa. The maximum plasma density values are observed at 90 W in the d.c. mode, reaching 1.41 × 1017 m−3, and 1.95 × 1016 m−3 in the RF mode, with results obtained within 1μs after ignition of the plasma. The results of the experiments showed that the plasma concentration at a distance of 23 mm from the cathode has maximum values; indicating that the electron and ion density values increase as the d.c. and RF magnetron sputtering power increases. This research aims to demonstrate the different charge density values obtained in RF and d.c. plasma with FEM to facilitate the prediction of the magnetron sputtering discharge parameters of the MatER PUCP laboratory. Given that at this moment suitable models for RF sputtering are rather scarce, the obtained plasma parameters from FEM will be compared to plasma parameters that were obtained experimentally.
12 June 2023 in Journal of Vacuum Science & Technology A
The self-propagating reaction in binary Al/Ru multilayers with two different bilayer thicknesses (89 and 178 nm, respectively) forming single-phase AlRu intermetallic compound is investigated experimentally and by means of phase-field simulations. Experimentally, the time-temperature evolution in free-standing films was recorded with a high-speed pyrometer, and the resulting microstructure was determined from electron backscatter diffraction measurements. The phase-field model is constructed based on the minimization of the grand potentials for which the required thermodynamic data are taken from the Calphad database. The simulation of the reaction and subsequent AlRu grain growth starts from Al-rich and Ru-rich layer fillings. After the formation of the AlRu phase is complete, the grain growth during cooling is simulated based on the experimentally recorded time-temperature curves. Finally, the resulting grain sizes obtained from the simulation are found to be in good agreement with the experimental results. Furthermore, it is shown that the final grain sizes in both simulations and experiments depend on the initial bilayer thicknesses.