Sven Ulrich

Prof. Dr. Sven Ulrich

orcid

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 March 2022 in Coatings
Verified
Journal Article
Open access
PDF file
JSJohannes Schneider
Johannes Schneider
SUSven Ulrich
Sven Ulrich
JPJörg Patscheider
Jörg Patscheider
Michael StueberMichael Stueber
Michael Stueber
Friction and wear performance of non-reactively magnetron-sputtered hydrogen-free TiC/a-C coatings were characterized under lubricated oscillating sliding conditions against 100Cr6 steel. The friction mediators, isooctane, ethanol and distilled water, were chosen to address the actual trend of environmentally friendly green technologies in mobility and the potential use of carbon-based nanocomposite thin film materials for tribocomponents in contact with gasoline and alternative biofuels. Sliding pairs of the TiC/a-C coatings showed significantly reduced friction and wear compared to the reference materials under both unlubricated and lubricated conditions (when using the aforementioned media isooctane, ethanol and distilled water). Quasi-stationary friction coefficient of the TiC/a-C sliding pairs after running-in was almost independent of test conditions and could be traced back to self-lubrication as a result of the formation of a transfer layer on the steel counter body. Wear of the coatings based on micro-abrasion and tribochemical reaction was significantly influenced by the environmental conditions. Lowest wear was measured after tests in non-polar isooctane whereas highest wear was measured after tests in water.

28 January 2022 in Coatings
Verified
Journal Article
Open access
PDF file
Chongchong TangChongchong Tang
Chongchong Tang
MSMartin Steinbrück
Martin Steinbrück
MGMirco Große
Mirco Große
SUSven Ulrich
Sven Ulrich
Michael StueberMichael Stueber
Michael Stueber
Elemental Cr/C/Al multilayers (stoichiometric ratio: 2:1:1) with and without a Cr overlayer have been synthesized on Zircaloy-4 substrates by magnetron sputtering. The effects of annealing temperatures (400 and 550 °C) on phase/microstructure formation, mechanical properties, and oxidation/corrosion performance have been comparatively studied. Annealing of the multilayers at 400 °C led to the formation of nanocrystalline composite consisting of intermetallic and binary carbide phases. Single-phase Cr2AlC was obtained after 550 °C annealing, but with microcracking of the coatings. Both annealed coatings displayed similar mechanical properties, high-temperature oxidation, and hydrothermal corrosion mechanisms. The composite coatings annealed at 400 °C significantly enhance the high-temperature oxidation resistance (α-Al2O3 scale growth) and hydrothermal corrosion (Cr2O3 passivation layer formation) of a Zircaloy-4 substrate without coating microcracking and delamination. Nanocomposite CrCAl-based coatings are promising candidates for coated ATF applications with acceptable processing temperatures and excellent oxidation/corrosion resistances for a zirconium alloy substrate.

11 January 2023 in Coatings
Verified
Journal Article
Open access
PDF file
VOVincent Ott
Vincent Ott
CSChristian Schäfer
Christian Schäfer
Sebastian SuarezSebastian Suarez
Sebastian Suarez
Karsten WollKarsten Woll
Karsten Woll
Frank MücklichFrank Mücklich
Frank Mücklich
Michael StueberMichael Stueber
Michael Stueber
In this study, we report on phase formation and microstructure evolution in multiscale magnetron sputtered Ru/Al multilayers upon thermal annealing in vacuum at slow heating rates of 10 K/min. By specifically adjusting the microstructure and design of the as-deposited multilayers, the formation of certain desired phases can be tuned. We demonstrate that the synthesis of single phase RuAl thin films is possible in a very controlled manner in a solid state only via thermal activation without initiating the self-propagating exothermic reactions of Ru/Al multilayers. To investigate phase formation sequences and the resulting microstructures, Ru/Al multilayers were designed via magnetron sputtering with systematic variation of bilayer modulation periods and subsequent vacuum annealing. Thin films samples were characterized by in situ high-temperature XRD, TEM imaging and diffraction. It is shown that different phase sequences appear in strong correlation with the modulation length. Depending on the multilayer design, the phase formation toward single-phase RuAl thin films happens as either a multi-step or single-step event. In particular, below a critical threshold of the modulation period, the multi-step phase formation can be suppressed, and only the desired RuAl target phase is obtained with a pronounced growth in a preferred orientation. This finding may be versatile for the targeted synthesis of intermetallic phases, contributing to further understanding of phase formation in such nanoscale multilayer systems.

20 April 2024 in Nanomaterials
Verified
Journal Article
Open access
PDF file
BNBerkin Nergis
Berkin Nergis
Sondes BauerSondes Bauer
Sondes Bauer
Xiaowei JinXiaowei Jin
Xiaowei Jin
LHLukáš Horák
Lukáš Horák
RSReinhard Schneider
Reinhard Schneider
TBTilo Baumbach
Tilo Baumbach
The morphology and crystal structure of Pt films grown by pulsed laser deposition (PLD) on yttria-stabilized zirconia (YSZ)at high temperatures Tg = 900 °C was studied for four different film thicknesses varying between 10 and 70 nm. During the subsequent growth of the capping layer, the thermal stability of the Pt was strongly influenced by the Pt film’s thickness. Furthermore, these later affected the film morphology, the crystal structure and hillocks size, and distribution during subsequent growth at Tg = 900 °C for a long duration. The modifications in the morphology as well as in the structure of the Pt film without a capping layer, named also as the as-grown and encapsulated layers in the bilayer system, were examined by a combination of microscopic and scattering methods. The increase in the thickness of the deposited Pt film brought three competitive phenomena into occurrence, such as 3D–2D morphological transition, dewetting, and hillock formation. The degree of coverage, film continuity, and the crystal quality of the Pt film were significantly improved by increasing the deposition time. An optimum Pt film thickness of 70 nm was found to be suitable for obtaining a hillock-free Pt bottom electrode which also withstood the dewetting phenomena revealed during the subsequent growth of capping layers. This achievement is crucial for the deposition of functional bottom electrodes in ferroelectric and multiferroic heterostructure systems.

8 July 2025 in JOM
Verified
Journal Article
Open access
PDF file
LBLena Burger
Lena Burger
HPHeinz Palkowski
Heinz Palkowski
SUSven Ulrich
Sven Ulrich
HMHadi Mozaffari-Jovein
Hadi Mozaffari-Jovein
With time, the benefits of additive manufacturing have become firmly established in the domain of medical technology. The high degree of design freedom and precision afforded by additive manufacturing enables the production of implant components that are precisely tailored to individual requirements and based on patient-specific data. In addition to the advantages, the production of such components presents process-related material science challenges. One such challenge of this manufacturing process is the residual stresses due to the occurring phase transformation during the rapid process-related cooling rates. These stresses can lead to component deformation and impair the mechanical load-bearing capacity of the component, leading to accelerated fatigue. This aim of this study is to analyse the various influences of manufacturing and machining processes such as heat-treatment or application-related stress on the residual stress state of additively manufactured components based on titanium alloys.

10 February 2026 in Materials
Verified
Journal Article
Open access
PDF file
DLDimitri Litvinov
Dimitri Litvinov
JAJarir Aktaa
Jarir Aktaa
ABAdam Bichler
Adam Bichler
Michael StueberMichael Stueber
Michael Stueber
SUSven Ulrich
Sven Ulrich
The structure and composition of a refractory Ni-containing CrMoNbTaVW high-entropy-alloy (HEA) thin film were investigated. The HEA thin film with a thickness of 5 μm was grown via conventional direct current magnetron sputtering from a multiple-elemental compound target. The Ni-containing HEA thin film with a Ni concentration of 3.6 at. % exhibits a single-phase body-centered cubic (BCC) crystal structure with a lattice parameter of a = 0.316 nm. The grains in the HEA thin film are columns, extended in the growth direction. They are not aligned exactly perpendicular to the substrate surface. The thin film grows in a polycrystalline structure with a tendency to preferred orientation or texture. Energy-dispersive X-ray analyses of the HEA thin film show near-equal atomic concentrations of Cr, Mo, Nb, Ta, V, and W elements in the range 15–17 at. % with almost uniform distribution. In contrast, Ni is not uniformly distributed in the film, and grains with a different Ni concentrations were observed. The defects observed in the HEA thin film are mainly single dislocations or an assembly of dislocations, which could be caused by residual stresses in the layer forming during the growth of the HEA thin film.