Photovoltaic (PV) panels and thermal collectors are commonly known as mature technologies to capture solar energy. The efficiency of PV cells decreases as operating cell temperature increases. Photovoltaic Thermal Collectors (PVT) offer a way to mitigate this performance reduction by coupling solar cells with a thermal absorber that can actively remove the excess heat from the solar cells to the Heat Transfer Fluid (HTF). In order for PVT collectors to effectively counter the negative effects of increased operating cell temperature, it is fundamental to have an adequate heat transfer from the cells to the HTF. This paper analyzes the operating temperature of the cells in a low concentrating PVT solar collector, by means of both experimental and Computational Fluid Dynamics (CFD) simulation results on the Solarus asymmetric Compound Parabolic Concentrator (CPC) PowerCollector (PC). The PC solar collector features a Compound Parabolic Concentrator (CPC) reflector geometry called the Maximum Reflector Concentration (MaReCo) geometry. This collector is suited for applications such as Domestic Hot Water (DHW). An experimental setup was installed in the outdoor testing laboratory at Gävle University (Sweden) with the ability to measure ambient, cell and HTF temperature, flow rate and solar radiation. The experimental results were validated by means of an in-house developed CFD model. Based on the validated model, the effect of collector tilt angle, HTF, insulation (on the back side of the reflector), receiver material and front glass on the collector performance were considered. The impact of tilt angle is more pronounced on the thermal production than the electrical one. Furthermore, the HTF recirculation with an average temperature of 35.1 °C and 2.2 L/min flow rate showed that the electrical yield can increase by 25%. On the other hand, by using insulation, the thermal yield increases up to 3% when working at a temperature of 23 °C above ambient.
A two-trough parabolic-shaped concentrating photovoltaic solar collector with a vertical half-size ‘phosphorus-passivated emitter rear totally diffused’ bifacial cell string receiver was designed and built for household applications, with the aim of smooth the electrical ‘duck curve’. The study consisted in testing the concentrating photovoltaic solar collector outdoors, under real weather conditions, for its daily electrical peak power and efficiency, as well as for its electrical transversal and longitudinal Incidence Angle Modifier direction. The outdoor testing measurements were conducted in a parabolic trough with low concentration coupled with a central vertical half-size ‘phosphorus-passivated emitter rear totally diffused’ bifacial cell string receiver. Furthermore, the electrical transversal Incidence Angle Modifier showed to be very delicate due to the position and outline of the receiver, which led to an electrical peak efficiency close to 10% at ±25° (i.e., for an electrical power output of around 49.3 W/m2). To validate the measured parameters, a ray-tracing software has been used, where the measured Incidence Angle Modifiers have a very good agreement with the simulated Incidence Angle Modifiers (e.g., deviation of <4%). Consequently, the concentrating solar collector met the objective of lowering the Photovoltaic cell stress and high radiation intensity, by shifting the electrical peak power at normal (e.g., at 0°) to higher incidence angles (e.g., ±25°); this aids the electrical demand peak shaving, by having the highest electrical power production displaced from the highest intensity solar radiation during the day.
Photovoltaics (PV) and Solar Thermal (ST) collectors are sometimes competitors, as investment capacity, energy demand, and roof space are limited. Therefore, a ratio that quantifies the difference in annual energy output between ST and PV for different locations is useful. A market survey assessing the average price and performance both in 2013 and 2021 was conducted, showing a factor of 3 cell price decrease combined with a 20% efficiency increase, while ST showed negligible variation. Winsun simulations were conducted, and the results were plotted on the world map. Despite variations due to local climate, the ratio of energy production (ST/PV) increases at lower latitudes mainly due to (a) higher air temperature increasing ST output but decreasing the PV output; (b) solar radiation reducing ST efficiency to zero while having a minor impact on PV efficiency. The ratio was calculated for several ST operating temperatures. For latitudes lower than 66°, the ratio of a flat plate at 50 °C to a PV module ranges from 1.85 to 4.46, while the ratio between a vacuum tube at 50 °C and a PV module ranges from 3.05 to 4.76. This ratio can support the decision between installing ST or PV while combining different factors such as energy value, system complexity, and installation cost.
The world’s energy system faces major challenges due to transitions from fossil fuels to other alternatives. An important part of the transition is energy-efficient homes that partially produce their own electricity. This paper explores the energy interactions between heating, cooling, and electricity usage in a planned residential area in Sweden where a significant portion of the electricity is generated by solar PV systems. Conventional district heating and cooling systems and a low-temperature district heating system that uses return cascading technology were compared with heat pump systems. Electricity sharing in an energy community has a low impact on the calculated national energy efficiency metric. It is also shown that electrifying space heating with heat pumps improves the calculated energy efficiency metric, but heat pumps increase the peak power demand in the winter due to high heat demand and a lack of solar production. Using heat pumps for heating domestic hot water and compressor chillers for cooling offers a more balanced use/production of electricity since the electric cooling load is mostly met by local solar production, as shown by an increase in self-consumption of 8% and stable self-sufficiency. There is, however, a time mismatch between production and the peak electricity demand, which could be addressed by using energy storage systems.