Integrated transmission-and-distribution (T&D) modeling is a new and developing method for simulating power systems. Interest in integrated T&D modeling is driven by the changes taking place in power systems worldwide that are resulting in more decentralized power systems with increasingly high levels of distributed energy resources. Additionally, the increasing role of the hitherto passive energy consumer in the management and operation of power systems requires more capable and detailed integrated T&D modeling to understand the interactions between T&D systems. Although integrated T&D modeling has not yet found widespread commercial application, its potential for changing the decades-old power system modeling approaches has led to several research efforts in the last few years that tried to (i) develop algorithms and software for steady-state and dynamic modeling of power systems and (ii) demonstrate the advantages of this modeling approach compared with traditional, separated T&D system modeling. In this paper, we provide a review of integrated T&D modeling research efforts and the methods employed for steady-state and dynamic modeling of power systems. We also discuss our current research in integrated T&D modeling and the potential directions for future research. This paper should be useful for power systems researchers and industry members because it will provide them with a critical summary of current research efforts and the potential topics where research efforts are needed to further advance and demonstrate the utility of integrated T&D modeling.
1 January 1991 in IEEE Transactions on Power Delivery
The use of a Graph Trace Analysis (GTA)-based power flow for analyzing the voltage stability of integrated Transmission and Distribution (T&D) networks is discussed in the context of distributed Photovoltaic (PV) generation. The voltage stability of lines and the load carrying capability of buses is analyzed at various PV penetration levels. It is shown that as the PV generation levels increase, an increase in the steady state voltage stability of the system is observed. Moreover, within certain regions of stability margin changes, changes in voltage stability margins of transmission lines are shown to be linearly related to changes in the loading of the lines. Two case studies are presented, where one case study involves a model with eight voltage levels and 784,000 nodes. In one case study, a voltage-stability heat map is used to demonstrate the identification of weak lines and buses.
This paper evaluates residential smart photovoltaic (PV) inverters’ responses to cyberattacks and assesses the performance of an intrusion detection strategy for smart grid devices by comparing time-series power flow results from a simulation application called Faster Than Real-Time (FTRT) Simulator to measurements from a Power Hardware-in-the-Loop (P-HIL) laboratory as a testbed. Twenty different cyberattacks from three classes - Denial of Service (DoS), Intermittent attack, and Modification - were designed and tested with grid-tied smart inverters in order to study the inverters’ responses to malicious activities. The intrusion detection strategy was developed using a comparison between the predicted PV power output from FTRT and the power flows measured from P-HIL laboratory through the API interface. Real and reactive power thresholds were assigned based on a number of repeated experiments to ensure the applicability of the thresholds. The results showed that inverters from different manufacturers have their own unique responses which could be detected by the power flow measurements. Our detection method could identify over 94% of actual malicious actions and 7.4% of no-attack hours are detected as false positives. Out of 38 under-attack hours, 2 undetected hours are due to the intermittent attacks. Different attacks can be detected based on the targeted components of the complex power that attackers are aiming to cause disturbances. Our findings additionally show that DoS can be noticed immediately after the devices have been sabotaged, and they can be detected from the active power analysis. However, modification attack detection will depend more on the reactive power measurements, while intermittent attacks remain the most challenging for the proposed detection method since the objective of intermittent attacks is to create an oscillation of the complex power components which need a relatively high time resolution for the measurement.
18 October 2010 in IEEE Transactions on Power Systems
Grid modernization strategies often focus on replacing aging distribution control equipment with state-of-the-art devices capable of remote monitoring, communication, and control. However, wholesale replacement of the existing distribution infrastructure may not be practical or economical. Additionally, even with improved capabilities, “smart” devices may still be ignorant of changes in circuit topology. This paper presents a model-based distribution control scheme that is independent of circuit topology and integrates legacy and modern control equipment. Simulation results indicate the proposed method can improve circuit performance under both normal and abnormal conditions.
27 December 2017 in IEEE Transactions on Industry Applications
Photovoltaic (PV) resources have introduced themselves as a main player in impacting different aspects of the power system from system planning to voltage stability. The main challenge of employing PV systems is the intermittent nature of solar energy. The irradiance variations are mainly caused by cloud motion and the associated shadows moving over solar arrays. Thus, when dealing with high PV penetration levels, simulation of cloud shadow motion and its effect on the power system is of interest. In this work, a cloud motion simulator (CMS) that incorporates quasi-steady-state power-flow analysis is introduced. Moreover, how the CMS parameters can be estimated from field data is discussed. Cloud motion and the consequent voltage fluctuations can cause voltage flicker issues. A new and practical method for calculating short-term flicker severity based on the IEEE 1453-2015 standard is introduced and discussed. Effects of cloud speed, number of clouds, width of clouds, and time interval between clouds on short-term flicker are investigated. In addition, the effect of using distributed models for larger PV systems on flicker severity is investigated.