Silicon nitride attracts increasing interest in integrated photonics owing to its low propagation loss and wide transparency window, extending from to 2350 nm. Scalable integration of active devices such as amplifiers and lasers on the platform will enable applications requiring optical gain and a much-needed alternative to hybrid integration, which suffers from high cost and lack of high-volume manufacturability. We demonstrate a high-gain optical amplifier in monolithically integrated on the platform using a double photonic layer approach. The device exhibits a net gain of at 1532 nm, and a broadband gain operation over 70 nm covering wavelengths in the S-, C- and L-bands. This work shows that rare-earth-ion-doped materials and in particular, rare-earth-ion-doped , can provide very high net amplification for the platform, paving the way to the development of different active devices monolithically integrated in this passive platform.
Nanophotonic waveguide enhanced Raman spectroscopy (NWERS) is a sensing technique that uses a highly confined waveguide mode to excite and collect the Raman scattered signal from molecules in close vicinity of the waveguide. The most important parameters defining the figure of merit of an NWERS sensor include its ability to collect the Raman signal from an analyte, i.e. "the Raman conversion efficiency" and the amount of "Raman background" generated from the guiding material. Here, we compare different photonic integrated circuit (PIC) platforms capable of on-chip Raman sensing in terms of the aforementioned parameters. Among the four photonic platforms under study, tantalum oxide and silicon nitride waveguides exhibit high signal collection efficiency and low Raman background. In contrast, the performance of titania and alumina waveguides suffers from a strong Raman background and a weak signal collection efficiency, respectively.
We demonstrate reactively sputtered Al2O3:Er3+ waveguide amplifiers with an erbium concentration of 3.9 × 1020 ions/cm3, capable of achieving over 30 dB small signal net gain at 1532 nm using bidirectional pumping at 1480 nm. We observe on chip output powers of 10.2-13.6 dBm of amplified signal power at 1532 nm for a 12.9 cm waveguide amplifier considering -25.4 dB of lumped coupling losses per facet. Annealing was used to improve the performance of the devices, which were patterned using electron beam lithography and reactive ion etching. This result, to our knowledge, represents record breaking on-chip internal net gain for Al2O3:Er3+ waveguide amplifiers, which show promise over other technologies due to wafer scalability and promise of easy monolithic integration with other material platforms to support a wide variety of applications.
Aluminum oxide (Al2O3) is an emerging material in integrated photonics. It exhibits a very broad transparency window from the UV to the mid-IR, very low propagation losses and a high solubility for rare-earth ions leading to optical gain in different spectral ranges. Al2O3 can be deposited by different wafer-level deposition techniques, including atomic layer deposition and reactive magnetron sputtering, being compatible with the monolithic integration onto passive integrated photonics platforms, such as Si3N4, to which it provides optical amplification and lasing. When deposited at low temperatures, it is also compatible with integration onto CMOS chips. In this review, the state-of-the-art on the deposition, integration and device development in this photonic platform is described. Graphical Abstract Graphical abstract
Self-referenced biosensing based on mode-splitting on a microring resonator is experimentally demonstrated. A Bragg grating integrated on the surface of the ring provides coupling between the clockwise and counterclockwise travelling modes of the pristine ring resonator lifting their degeneracy. The amount of mode-splitting is directly related to the reflectivity of the grating and it is only affected by structurally modifying the grating. Environmental perturbations to the surroundings of the gratings, such as temperature and bulk refractive index variations, have a minor effect on the amount of mode-splitting. This principle allows the realization of a self-referenced sensing scheme based on the detection of variations of the mode-splitting induced by structural changes to the grating. In this work, a polymethyl methacrylate (PMMA) Bragg grating is integrated onto a ring resonator in Al2O3. It is shown both theoretically and experimentally that the amount of splitting of a resonance varies minimally under temperature or bulk refractive index perturbations. However, the structural change of attaching a layer of biomolecules inside the grating does affect its reflectivity and the amount of mode splitting present. This result represents the first proof-of-concept demonstration of an integrated mode-splitting biosensor insensitive to temperature and refractive index variations of the liquid matrix where the molecules to be detected are embedded. The reported results pave the road towards the realization of truly self-referenced biosensors.
TiO2 channel waveguides were fabricated using a DC sputter deposition process, followed by photolithography and reactive ion etching. A SiO2 cladding was deposited using evaporation. SEM, TEM and Raman measurements indicate the presence of both an amorphous and a crystalline phase. As the layer thickness increases, poly-crystalline structures start forming. Loss measurements were performed by imaging the scattered light from the top of the channel waveguides and fitting an exponential decay to the intensity profile. Propagation losses of 7.8 ± 0.52 dB/cm at a wavelength of 632.8 nm and 0.68 ± 0.46 dB/cm at a wavelength of 1010 nm were experimentally characterized.