23 December 2020 in Optics Express
Self-referenced biosensing based on mode-splitting on a microring resonator is experimentally demonstrated. A Bragg grating integrated on the surface of the ring provides coupling between the clockwise and counterclockwise travelling modes of the pristine ring resonator lifting their degeneracy. The amount of mode-splitting is directly related to the reflectivity of the grating and it is only affected by structurally modifying the grating. Environmental perturbations to the surroundings of the gratings, such as temperature and bulk refractive index variations, have a minor effect on the amount of mode-splitting. This principle allows the realization of a self-referenced sensing scheme based on the detection of variations of the mode-splitting induced by structural changes to the grating. In this work, a polymethyl methacrylate (PMMA) Bragg grating is integrated onto a ring resonator in Al2O3. It is shown both theoretically and experimentally that the amount of splitting of a resonance varies minimally under temperature or bulk refractive index perturbations. However, the structural change of attaching a layer of biomolecules inside the grating does affect its reflectivity and the amount of mode splitting present. This result represents the first proof-of-concept demonstration of an integrated mode-splitting biosensor insensitive to temperature and refractive index variations of the liquid matrix where the molecules to be detected are embedded. The reported results pave the road towards the realization of truly self-referenced biosensors.
1 June 2016 in Optics Express
We demonstrate an integrated optical probe including an on-chip microlens for a common-path swept-source optical coherence tomography system. This common-path design uses the end facet of the silicon oxynitride waveguide as the reference plane, thus eliminating the need of a space-consuming and dispersive on-chip loop reference arm, thereby obviating the need for dispersion compensation. The on-chip micro-ball lens eliminates the need of external optical elements for coupling the light between the chip and the sample. The use of this lens leads to a signal enhancement up to 37 dB compared to the chip without a lens. The light source, the common-path arm and the detector are connected by a symmetric Y junction having a wavelength independent splitting ratio (50/50) over a much larger bandwidth than can be obtained with a directional coupler. The signal-to-noise ratio of the system was measured to be 71 dB with 2.6 mW of power on a mirror sample at a distance of 0.3 mm from the waveguide end facet. Cross-sectional OCT images of a layered optical phantom sample are demonstrated with our system. A method, based on an extended Fourier-domain OCT model, for suppressing ghost images caused by additional parasitic reference planes is experimentally demonstrated.
3 April 2019 in IEEE Journal of Selected Topics in Quantum Electronics
Low-cost, high-performance integration technologies are instrumental for active-passive integrated photonics devices. The monolithic integration of $\rm Al_{2}O_{3}$ and $\rm Si_{3}N_{4}$ is studied, enabling to combine the promising optical features of $\rm Si_{3}N_{4}$ with the excellent optical gain characteristics of rare-earth-ion doped $\rm Al_{2}O_{3}$ . The $\rm Al_{2}O_{3}$ and $\rm Si_{3}N_{4}$ layers are separated by a thin SiO2 film and coupled by adiabatically width-tapered $\rm Al_{2}O_{3}$ and thickness-tapered $\rm Si_{3}N_{4}$ waveguides. In this work, a detailed characterization of the couplers as well as a study of the influence of the different design parameters and fabrication tolerances on the final device performance is presented. Test structures are characterized under TE polarization. Measured loss per coupler is as low as 0.26±0.03 dB at the wavelength of 1030 nm, and below 0.24 dB in the spectral window of 1460-1635 nm. Lateral misalignment of ±1 μm results in less than 0.6 dB increase of the coupler loss at 1030 nm, and the tolerance of misalignment goes up to 1.7 μm at the investigated longest wavelength of 1635 nm without introducing extra coupler losses. The reported integration technology paves the way towards a double-layer platform monolithically integrating $\rm Si_{3}N_{4}$ and rare-earth-ion doped $\rm Al_{2}O_{3}$ for active-passive photonic functionalities.
17 August 2015 in Optics Express
We demonstrate a fabrication procedure for the direct integration of micro-ball lenses on planar integrated optical channel waveguide chips with the aim to reduce the divergence of light that arises from the waveguide in both horizontal and vertical directions. Fabrication of the lenses is based on photoresist reflow which is a procedure that allows for the use of photolithography for careful alignment of the lenses with respect to the waveguides and enables mass production. We present in detail the design and fabrication procedures. Optical characterization of the fabricated micro-ball lenses demonstrates a good performance in terms of beam-size reduction and beam shape. The beam half divergence angle of 1544 nm light is reduced from 12.4 ° to 1.85 °.
16 January 2024 in Optics Express
Miniature free-space optical beams, originating from on-chip microstructures, are usually measured and quoted without reference to a particular polarization state. We develop an automated platform to characterize tightly focused free-space optical beams in three dimensions. We present a detailed description of each subsystem including the calibration and test procedure. We demonstrate how amplitude and phase are measured at sub-wavelength resolution using a cleaved fiber with a heterodyne reference. Further analysis provides information about the phase and intensity profile of the beam with regards to its polarization content and spatial confinement. We perform a proof-of-concept experiment for a custom waveguide-coupled micro-mirror. The work opens new possibilities for rapid analysis of micro-mirrors in prototyping and optimization of integrated optical systems.
8 January 2021 in Optics Express
We propose and experimentally demonstrate a modular microring laser (MML) cavity for sensing applications. The proposed MML permits much more design freedom compared with a traditional simple ring cavity by decoupling the performance parameters into several regions in the cavity. Thus, the different biosensor performance parameters can be optimized semi-independently limiting the need for trade-offs on the design of the biosensing device. The first generation MML has been fabricated and tested. A fiber-to-fiber slope efficiency of up to 1.2%, a temperature coefficient of 1.35 GHz/K and a 3σ limit of detection (LOD) of 3.1 × 10−7 RIU without averaging and 6.0 × 10−8 RIU with a 60 s averaging, has been measured for the MML sensor, which is a record-low LOD in on-chip ring cavity optical sensors. Further optimization is possible, capitalizing on the key advantage of the MML concept, namely the potential for designing the laser cavity to achieve the desired optimization goals.