Forces induced by quantum fluctuations of the electromagnetic field control adhesion phenomena between rough solids when the bodies are separated by distances of approximately . However, this distance range remains largely unexplored experimentally in contrast with the shorter (van der Waals forces) or the longer (Casimir forces) separations. The reason for this is the pull-in instability of the systems with the elastic suspension that poses a formidable limitation. In this paper we propose a genuine experimental configuration that does not suffer from the short distance instability. The method is based on the adhered cantilever, whose shape is sensitive to the forces acting near the adhered end. The general principle of the method, its possible realization, and feasibility are extensively discussed. The dimensions of the cantilever are determined by the maximum sensitivity to the forces. If the adhesion is defined by strong capillary or chemical interactions, the method loses its sensitivity. Special discussion is presented for the determination of the minimum distance between the rough solids upon contact, and for the compensation of the residual electrostatic contribution. The proposed method can be applied to any kind of solids (metals, semiconductors, or dielectrics) and to any intervening medium (gas or liquid).
Combustion reactions quench in small volumes due to fast heat escape via the volume boundary. Nevertheless, the reaction between hydrogen and oxygen was observed in nano- and micro-bubbles. The bubbles containing a mixture of gases were produced in microsystems using electrochemical decomposition of water with a fast switching of voltage polarity. In this paper, we review our experimental results on the reaction in micro- and nano-bubbles and provide their physical interpretation. Experiments were performed using microsystems of different designs. The process was observed with a stroboscope and with a vibrometer. The latter was used to measure the gas concentration in the electrolyte and to monitor pressure in a reaction chamber covered with a flexible membrane. Information on the temperature was extracted from the Faraday current in the electrolyte. Since the direct observation of the combustion is complicated by the small size and short time scale of the events, special attention is paid to the signatures of the reaction. The mechanism of the reaction is not yet clear, but it is obvious that the process is surface dominated and happens without significant temperature increase.
Water electrolysis with a fast change of polarity generates a high concentration of bulk nanobubbles containing H and O gases. When this concentration reaches a critical value, a microbubble pops up, which is terminated quickly in an explosion process. In this paper, we provide experimental information on the phenomenon concentrating on the dynamics of exploding microbubble observed from the top and from the side. An initial bubble with a size of m expands to a maximum size of m for s and then shrinks in the cavitation process. The sound produced by the event is coming from two sources separated in time: exploding bubble and cavitating bubble. The observed dynamics supports expansion of the bubble with steam but not with H and O mixture. A qualitative model of this puzzling phenomenon proposed earlier is refined. It is demonstrated that the pressure and temperature in the initial bubble can be evaluated using only the energy conservation law for which the driving energy is the energy of the combusted gas. The temperature in the bubble reaches 200 C that shows that the process cannot be ignited by standard combustion, but the surface-assisted spontaneous combustion agrees well with the observations and theoretical estimates. The pressure in the microbubble varies with the size of the merging nanobubbles and is evaluated as 10–20 bar. Large pressure difference between the bubble and liquid drives the bubble expansion, and is the source of the sound produced by the process. Exploding microbubbles are a promising principle to drive fast and strong micropumps for microfluidic and other applications.
Dispersion forces start to play role in modern micro/nanoelectromechanical devices, but the methods to measure these forces at distances close to contact (<50 nm) suffer from pull-in instability. The method of adhered cantilever proposed recently has no instability and is able to make measurements at short separations. To measure the force at the average distance between surfaces in contact, one has to know the shape of an elastic beam with one end fixed at a height of 1–10 μm and the other end adhered to the substrate. The maximum contribution to this shape from the dispersion forces is in a range of 30–100 nm, which is well measurable by the interferometric methods. This paper describes the instrument, measurements, and data processing that make possible the reconstruction of the beam shape with an accuracy of 1 nm in a height range of at least 5000 nm. Critical steps of the fabrication procedure of cantilevers that are 12 mm long, 200 μm wide, and 10 μm thick are described. The interferometer measures the shape based on the differential interference-contrast method; the scanning is realized by a stage with a step of 0.1 μm. The signal recorded from the adhered cantilever has a noise level of 0.33 nm at a maximum sensitivity in a frequency band of 20 MHz. It is concluded that the instrument and data processing algorithm can be used to measure the dispersion forces and adhesion energies between rough surfaces in unloaded contact.
Water electrolysis with a fast change of the polarity pumps in the liquid a huge amount of hydrogen and oxygen gases. In contrast with the DC electrolysis the gases do not form visible bubbles but change significantly the refractive index of the liquid nearby the electrodes from n = 1.35 to the values smaller than 1.19. The decrease of n is registered as distortion of the images of the electrodes. We argue that all the gas is collected in H2 and O2 nanobubbles with a size smaller than 200 nm. The concentration of nanobubbles with a size of 100 nm is estimated as 1021 m−3. Due to a significant contribution from the Laplace pressure the effective supersaturation reaches 500 for hydrogen and 150 for oxygen.