Based on finite element simulation analysis, laminated ceramic tool materials with different structures were designed and the effect of laminated structure on tool state was investigated. Residual stresses in ceramic tool materials increase with the number of layers and layer–thickness ratio. Based on the simulation results, SiAlON-SiC-SiCw/SiAlON-Al₂O₃ ceramic tool materials (SCWAs) were prepared using the spark plasma sintering process, and the influence of residual stress on the mechanical properties and microstructure of laminated ceramic tool materials was studied. The mechanical properties of ceramic materials were significantly improved under the effect of residual stresses. The fracture toughness of SCWA4 with 7 layers and a layer–thickness ratio of 6 was 6.02 ± 0.19 MPa·m^1/2, and the front and side flexural strengths were 602 ± 19 MPa and 595 ± 17 MPa, 36.3% and 39.0% higher than homogeneous SiAlON ceramics, respectively.

In this paper, the microstructures of nanocomposite ceramic tool materials are represented through Voronoi tessellation. A cohesive element model is established to perform the crack propagation simulation by introducing cohesive elements with fracture criteria into microstructure models. Both intergranular and transgranular cracking are considered in this work. The influences of nanoparticle size, microstructure type, nanoparticle volume content and interface fracture energy are analyzed, respectively. The simulation results show that the nanoparticles have changed the fracture pattern from intergranular mode in single-phase materials to intergranular–transgranular–mixed mode. It is mainly the nanoparticles along grain boundaries that have an impact on the fracture pattern change in nanocomposite ceramic tool materials. Microstructures with smaller nanoparticles, in which there are more nanoparticles dispersed along matrix grain boundaries, have higher fracture toughness. Microstructures with a nanoparticle volume content of 15% have the most obvious transgranular fracture phenomenon and the highest critical fracture energy release rate. A strong interface is useful for enhancing the fracture toughness of nanocomposite ceramic tool materials.

The continuous advancement of technology has led to escalating demands for superior tribological performance in industrial applications, necessitating the enhancement of ceramic materials’ frictional properties through innovative approaches. Solid-lubricant embedding is a widely employed lubrication strategy in metals. However, the challenge of machining holes on ceramic surfaces remains a significant barrier to applying this lubrication technique to ceramics. Gel casting, as a near-net-shaping process, offers several advantages, including uniform green body density, low organic content, and the capability to fabricate components with complex geometries, making it a promising solution for addressing these challenges. In this study, alumina ceramics with small surface holes designed for embedding oil-containing microcapsules were fabricated via gel casting using an N-hydroxy methylacrylamide gel system, which demonstrates lower toxicity compared to conventional acrylamide systems. The fabricated alumina ceramic materials exhibited a high density of 98.2%, a hardness of 16 GPa, and a bending strength of 276 MPa. The oil-containing microcapsules were self-synthesized using hexafluorophosphate ionic liquid as the core material and polyurea-formaldehyde as the wall material. The research results show that under conditions of using an alumina ball, sliding speed of 10 cm/min, load of 5 N, and at room temperature, the material with a microcapsule content of 15 wt% and embedded hole diameter of 1.2 mm reduced the friction coefficient from 0.696 in an unlubricated condition to 0.317. Moreover, the embedding of microcapsules further improved the wear resistance of the alumina.

To address the poor thermal shock resistance and high brittleness of traditional ceramic tools, a novel Si₃N₄/Sc₂W₃O₁₂ (SNS) composite ceramic material was developed via in situ synthesis using WO₃ and Sc₂O₃ as precursors and consolidated by spark plasma sintering. Sc₂W₃O₁₂ with negative thermal expansion was introduced to compensate for matrix shrinkage and modulate interfacial stress. The effects of varying Sc₂W₃O₁₂ content on thermal expansion, residual stress, microstructure, and mechanical properties were systematically investigated. Among the compositions, SNS3 (12 wt.% Sc₂W₃O₁₂) exhibited the best overall performance: relative density of 98.8 ± 0.2%, flexural strength of 712.4 ± 30 MPa, fracture toughness of 7.5 ± 0.3 MPa·m^1/2, Vickers hardness of 16.3 ± 0.3 GPa, and an average thermal expansion coefficient of 2.81 × 10⁻⁶·K⁻¹. The formation of a spherical chain-like Sc-W-O phase at the grain boundaries created a “hard core–soft shell” interface that enhanced crack resistance and stress buffering. Cutting tests showed that the SNS3 tool reduced workpiece surface roughness by 32.91% and achieved a cutting distance of 9500 m. These results validate the potential of this novel multiphase ceramic system as a promising candidate for high-performance and thermally stable ceramic cutting tools.