Today, two different types of CAD-CAM fabrication methods for complete denture bases are available besides the conventional protocols: a subtractive milling process from a prepolymerized block of polymethylmethacrylate and an additive manufacturing process that built the denture base using a light-cured liquid in a VAT-polymerization process. The aim of this study was to evaluate and to compare the accuracy and precision of denture prosthetic bases made with subtractive and additive manufacturing technologies and to compare them with a denture base with the conventional method in muffle. From the results obtained, 3D printing dentures show a statistically significant higher accuracy than milled prosthetic bases. Milled prosthetic bases have similar accuracy than conventional fabricated dentures.
Background: To compare the loss of preload in absence of loading and after a fixed number of cyclic loadings on 7-mm distal cantilever in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400,000 repeated loadings were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400,000 cyclic loadings; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 min from the tightening in absence of cyclic loadings. Conclusions: Within the limits of the present study, MUA and OT-Bridge may be considered reliable prosthetic anchoring systems able to tolerate repeated cyclic occlusal loads on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening.
Zygomatic implant rehabilitation is a challenging procedure that requires an accurate prosthetic and implant plan. The aim of this study was to evaluate the malar bone available for three-dimensional zygomatic implant placement on the possible trajectories exhibiting optimal occlusal emergence. After a preliminary analysis on 30 computed tomography (CT) scans of dentate patients to identify the ideal implant emergencies, we used 80 CT scans of edentulous patients to create two sagittal planes representing the possible trajectories of the anterior and posterior zygomatic implants. These planes were rotated clockwise on the ideal emergence points and three different hypothetical implant trajectories per zygoma were drawn for each slice. Then, the engageable malar bone and intra- and extra-sinus paths were measured. It was possible to identify the ideal implant emergences via anatomical landmarks with a high predictability. Significant differences were evident between males and females, between implants featuring anterior and those featuring posterior emergences, and between the different trajectories. The use of internal trajectories provided better bone engagement but required a higher intra-sinus path. A significant association was found between higher intra-sinus paths and lower crestal bone heights.
This study aimed to investigate the influence of three Implant Scan Bodies (ISBs), four intraoral scanners (IOSs), and two scan strategies on the trueness of complete arch implant scans. A reference digital cast of an all-on-six maxillary rehabilitation was obtained using a coordinate measuring machine. Three ISBs - AQ (ISB-AQ), One-shot, Elos (ISB-PEEK) - four IOSs - Trios3POD (TRIOS), Medit i700 (MED), iTero Element 5D (iTe), Primescan (PRIME) - and two scan strategies - Zig-zag (ZZ), One-shot (OS) - were used for evaluation. For each group created by the combination of the different variables, 10 digital scans were taken by one operator (n = 240) under controlled temperature and lighting conditions. The positions of the ISB connections were compared to the standard tessellation language reference file by using the nurbs-to-nurbs method. The overall 3D linear and angular deviations of the ISBs connections between reference and test scans were evaluated by computing the Euler distances (α=0.05). Interimplant distance discrepancies were calculated at the ISB connection level. Scanning times were recorded. Regarding linear and angular deviations, AQ had significantly higher trueness than the other ISBs (p < 0.01). TRIOS showed significantly higher trueness (p < 0.01). No significant differences for scan strategies were found (p > 0.05). ISB-OneSh, Primescan and ZZ method resulted in significant shortest scanning times (p<<0.01). ISB-AQ demonstrated higher trueness than One-Shot and PEEK. TRIOS performed better than the other IOSs. Scan strategy didn't influence the trueness. ISB-OneSh, Primescan, and ZZ strategy allowed the fastest scans. The choice of ISB and IOS significantly affects the accuracy of complete-arch implant scans. The scan strategy did not impact trueness but influenced the efficiency. As an in vitro study, results observed need confirmation in the clinical settings.
Background: The prosthetic preparation of the teeth for ceramic laminate veneers has to follow the minimally invasive concept brought by the modern Conservative Dentistry and Prosthodontics. However, during the cementation phase under the rubber dam, the loss of the esthetics landmarks could lead to errors in the future positioning of the laminate veneers. Methods: In this article the authors show an accurate operative prosthetic protocol using different fine intraoperative maneuvers and tricks for the realization of ceramic laminates in order to solve the problems of the cementation phase. Results: The treatment of the anterior sector of the upper maxilla with porcelain laminate veneers was realized in a 30 years old woman with aesthetic issues. Conclusion: Different fine intraoperative maneuvers and tricks during teeth preparation, master impression and rubber dam positioning could reduce errors occurring in the cementation phase and increase the predictability of the results.
The aim of this study was to evaluate the survival and clinical success rate, complications, and patients’ quality of life after computer-aided rehabilitation supported by zygomatic implants in cases of severe maxillary atrophy (ten patients) and in bone defects in oncologic patients (ten patients). All patients underwent computer-aided planning and surgery. Seventy-three zygomatic implants were placed. The mean follow-up period was 39.9 months. Implant survival and clinical success rate, the effectiveness of planning the implant length, biological and prosthetic complications, and the quality of life were evaluated. The five-year implant survival rate for patients with maxillary atrophy and oncologic patients was 97.4% and 96.7%, respectively. The prosthetic survival rate was 100%. Two implant failures occurred in the first year. One implant failure was observed in each group. Minor biological and prosthetic complications occurred in both groups without significant differences. All complications were managed without affecting the treatment. The quality of life increased by 71.3% in the atrophic group and by 82.9% in the oncologic group. Zygomatic implant rehabilitation seems to be a reliable technique for patients with maxillary atrophy and for oncologic patients. The three-dimensional computer-aided approach allows the surgeon to plan the surgery and increase its predictability. Early prosthesis loading certainly allows for better functional outcomes.