Davor Gracin

Dr. Davor Gracin

Institute Ruder Boskovic, Zagreb, Croatia

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 July 2022 in Materials
Verified
Journal Article
Open access
PDF file
KJKrunoslav Juraić
Krunoslav Juraić
PDPavo Dubček
Pavo Dubček
Mario BohačMario Bohač
Mario Bohač
Andreja GajovićAndreja Gajović
Andreja Gajović
SBSigrid Bernstorff
Sigrid Bernstorff
Davor GracinDavor Gracin
Davor Gracin
Fluorine-doped tin oxide thin films (SnO2:F) are widely used as transparent conductive oxide electrodes in thin-film solar cells because of their appropriate electrical and optical properties. The surface morphology of these films influences their optical properties and therefore plays an important role in the overall efficiencies of the solar cells in which they are implemented. At rough surfaces light is diffusely scattered, extending the optical path of light inside the active layer of the solar cell, which in term improves light absorption and solar cell conversion efficiency. In this work, we investigated the surface morphology of undoped and doped SnO2 thin films and their influence on the optical properties of the films. We have compared and analysed the results obtained by several complementary methods for thin-film surface morphology investigation: atomic force microscopy (AFM), transmission electron microscopy (TEM), and grazing-incidence small-angle X-ray scattering (GISAXS). Based on the AFM and TEM results we propose a theoretical model that reproduces well the GISAXS scattering patterns.

9 February 2007 in Journal of Applied Crystallography
Verified
Journal Article
Open access
PDF file
Davor GracinDavor Gracin
Davor Gracin
SBSigrid Bernstorff
Sigrid Bernstorff
PDPavo Dubcek
Pavo Dubcek
AGAndreja Gajovic
Andreja Gajovic
KJKrunoslav Juraić
Krunoslav Juraić

16 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
VKVedran Kojić
Vedran Kojić
Mario BohačMario Bohač
Mario Bohač
ADArijeta Bafti Dunatov
Arijeta Bafti Dunatov
Luka PavićLuka Pavić
Luka Pavić
KSKrešimir Salamon
Krešimir Salamon
Andreja GajovićAndreja Gajović
Andreja Gajović
In this paper, we studied the influence of polyvinylpyrrolidone (PVP) as a stabilization additive on optical and electrical properties of perovskite formamidinium lead iodide (FAPI) polycrystalline thin films on ZnO nanorods (ZNR). FAPI (as an active layer) was deposited from a single solution on ZNR (low temperature processed electron transport layer) using a one-step method with the inclusion of an anti-solvent. The role of PVP in the formation of the active layer was investigated by scanning electron microscopy and contact angle measurements to observe the effect on morphology, while X-ray diffraction was used as a method to study the stability of the film in an ambient environment. The effect of the PVP additive on the optical and electrical properties of the perovskite thin films was studied via photoluminescence, UV-Vis measurements, and electrical impedance spectroscopy. We have demonstrated that PVP inclusion in solution-processed perovskite FAPI thin films prevents the degradation of the film in an ambient atmosphere after aging for 2 months. The inclusion of the PVP also improves the infiltration of FAPI perovskite into ZnO nanostructures, increases electrical conductivity and radiative recombination of the photo-generated charge carriers. These results show promising information for promoting PVP stabilized FAPI perovskites for the new generation of photovoltaic devices.

1 November 2019 in Molecules
Verified
Journal Article
Open access
PDF file
IPIvana Panzic
Ivana Panzic
KJKrunoslav Juraić
Krunoslav Juraić
Nikša KrstulovićNikša Krstulović
Nikša Krstulović
AŠAna Šantić
Ana Šantić
DBDomagoj Belic
Domagoj Belic
Andreja GajovićAndreja Gajović
Andreja Gajović
ZnO has prominent electron transport and optical properties, beneficial for photovoltaic application, but its surface is prone to the formation of defects. To overcome this problem, we deposited nanostructured TiO2 thin film on ZnO nanorods to form a stable shell. ZnO nanorods synthesized by wet-chemistry are single crystals. Three different procedures for deposition of TiO2 were applied. The influence of preparation methods and parameters on the structure, morphology, electrical and optical properties were studied. Nanostructured TiO2 shells show different morphologies dependent on deposition methods: (1) separated nanoparticles (by pulsed laser deposition (PLD) in Ar), (2) a layer with nonhomogeneous thickness (by PLD in vacuum or DC reactive magnetron sputtering), and (3) a homogenous thin layer along the nanorods (by chemical deposition). Based on the structural study, we chose the preparation parameters to obtain an anatase structure of the TiO2 shell. Impedance spectroscopy shows pure electron conductivity that was considerably better in all the ZnO@TiO2 than in bare ZnO nanorods or TiO2 layers. The best conductivity among the studied samples and the lowest activation energy was observed for the sample with a chemically deposited TiO2 shell. Higher transparency in the visible part of spectrum was achieved for the sample with a homogenous TiO2 layer along the nanorods, then in the samples with a layer of varying thickness.

17 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
KJKrunoslav Juraić
Krunoslav Juraić
Davor GracinDavor Gracin
Davor Gracin
Matija ČuloMatija Čulo
Matija Čulo
ŽRŽeljko Rapljenovic
Željko Rapljenovic
JPJasper Plaisier
Jasper Plaisier
Mario BohačMario Bohač
Mario Bohač
Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO2), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 1020 cm−3 and 10–20 cm2/Vs, which are typical values for SnO2 films, and show a negligible temperature dependence from room temperature down to −269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO2 samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

2 September 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
KJKrunoslav Juraić
Krunoslav Juraić
Mario BohačMario Bohač
Mario Bohač
JPJasper Plaisier
Jasper Plaisier
AHAden Hodzic
Aden Hodzic
PDPavo Dubček
Pavo Dubček
Andreja GajovićAndreja Gajović
Andreja Gajović
In this work, we have investigated the potential dual application of TiO2 thin films as a photocatalyst for ammonia degradation, and as a UV light blocking layer in c-Si photovoltaics. For this purpose, we deposited a series of TiO2 thin films on a glass substrate by reactive magnetron sputtering and analysed the influence of the deposition parameters (O2/Ar working gas content and pressure) on the structural, optical and photocatalytic properties. All samples are nanocrystalline anatase TiO2 and have a uniform surface (RMS roughness < 5 nm) in a wide range of magnetron sputtering deposition parameters. They are transparent in the Vis/NIR spectral range and strongly absorb light in the UV range above the optical bandgap energy (3.3 eV), which makes them suitable for the use as UV blocking layers and photocatalysts. The photocatalytic properties were studied in a mini-photocatalytic wind tunnel reactor by examining ammonia degradation. A kinetic study was performed to estimate the reaction rate constants for all samples. The intrinsic reaction rate constant confirmed the crucial role of surface morphology in ammonia decomposition efficiency.