With the background of the fossil fuel energy crisis, the development of self-healing and recyclable polymer materials has become a research hotspot. In this work, a kind of cross-linking agent with pendent furan groups was first prepared and then used to produce the Polyurethane elastomer based on Diels–Alder chemistry (EPU–DA). In addition, in order to further enhance the mechanical properties of the elastomer, cellulose nanofibers (CNFs) were added into the Polyurethane system to prepare a series of composites with various contents of CNF (wt% = 0.1~0.7). Herein, the FTIR and DSC were used to confirm structure and thermal reversible character. The tensile test also indicated that the addition of CNF increased the mechanical properties compared to the pure Polyurethane elastomer. Due to their reversible DA covalent bonds, the elastomer and composites were recycled under high-temperature conditions, which extends Polyurethane elastomers’ practical applications. Moreover, damaged coating can also be repaired, endowing this Polyurethane material with good potential for application in the field of metal protection.
Magnetron-sputtered WS2 composite thin films are solid lubricants with excellent performances. However, the low hardness of the WS2 thin films necessitates the further improvement of their wear resistance. For this purpose, an effective strategy is to alternately deposit or code posit WS2 and a hard phase, such as TiB2, to form hard lubricant thin films. Herein, a TiB2 thin film was prepared under the same conditions as those used for depositing the WS2 thin film with a dense structure and excellent tribological properties. Because of the high deposition energy of high-power impulse magnetron sputtering (HiPIMS), the TiB2 thin film possesses a dense structure and leather-like flat surface (hardness = 24.17 GPa). The friction coefficient of the film under different loads ranges between 0.6 and 0.8. The wear rate of the thin film increases with load, mainly because of fatigue wear and abrasive wear. Under high loads, obvious furrow-like wear marks are observed. At different sliding frequencies, except 8 Hz, the friction coefficient of the film ranges from 0.6 to 0.8. The main wear mode is fatigue wear, particularly at increasing sliding frequencies. Although the film possesses a relatively high friction coefficient, its wear resistance is excellent (minimum wear rate = 1.96 × 10−6 mm3/(N·m)).
The exploration of unleaded free-cutting Cu40Zn brass with excellent mechanical and tribological properties has always drawn the attention of researchers. Due to its attractive properties combining metals and ceramics, Ti3AlC2 was added to Cu40Zn brass using high-energy milling and hot-pressing sintering. The effects of Ti3AlC2 on the microstructure, mechanical and tribological properties of Cu40Zn-Ti3AlC2 composites were studied. The results showed that Ti3AlC2 could suppress the formation of ZnO by adsorbing oxygen impurity and promote the formation of the β phase by releasing the β-forming element Al to the substrate. The hardness and wear resistance of Cu40Zn-Ti3AlC2 composites increased with increasing Ti3AlC2 content from 0 to 5 wt.%. The proper Ti3AlC2 additive was beneficial to both the strength and plasticity of the composites. The underlying mechanisms were discussed.
To address the limitations of single-layer nitride coatings, such as poor load adaptability and low long-term durability, MoN/TiN multilayer coatings were prepared via high-power impulse magnetron sputtering (HiPIMS). HiPIMS produces highly ionized plasmas that enable intense ion bombardment, yielding nitride films with enhanced mechanical strength, durability, and thermal stability versus conventional methods. The multilayer coating demonstrated a low coefficient of friction (COF, ~0.4) and wear rate (1.31 × 10−7 mm3/[N·m]). In contrast, both TiN and MoN coatings failed at 5 N and 10 N loads, respectively. Under increasing loads, the multilayer coating maintained stable wear rates (1.84–3.06 × 10−7 mm3/[N·m]) below 20 N, and ultimately failed at 25 N. Furthermore, the MoN layer contributes to COF reduction. Grazing-incidence X-ray diffraction analysis confirmed the enhanced crystallographic stability of the multilayer coating, thereby revealing a dominant (111) orientation. The multilayer architecture suppresses crack propagation while effectively balancing hardness and toughness, offering a promising design for extreme-load applications.
6 November 2018 in IOP Conference Series: Materials Science and Engineering
Benefitting from it novel structure, MoS2-TiL/MoS2-TiH nano multilayer coating possesses excellent tribological properties. The multilayer coating was prepared by varying the power of Ti target alternatively using magnetron sputtering technology. To investigate its tribological properties, more extensively analyses have been carried out on a reciprocating friction and wear testing machine under different loads. Then, wear trace morphology was studied by a confocal microscope. The friction coefficient is very stable around 0.1 ~ 0.2 at a load smaller than 20 N. Correspondingly, wear trace is narrow and the wear loss is very small under a small load. With a larger load, wear traces become wider and the lubricant only lasted for a short time. Whereas, compared to MoS2-Ti composite coating, the multilayer coating has the advantage apparently on wear resistance and lubrication.
Silicon oxycarbide thin film was prepared by magnetron sputtering on BK7 glass, namely, K9 glass. And the wavelength dependence of refractive index was determined by the envelop method and Wemple and Didomenico dispersion relationship from transmission spectrum. The wavelength dependence of refractive index was fitted to Cauchy dispersion relationship and the data accorded with Cauchy dispersion relationship very well. Thickness of the film was determined and by comparing the relative standard deviation, we found it could make the result more accurate by fitting the data of refractive index to Cauchy dispersion relationship.