Tao Yang

Dr. Tao Yang


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 March 2023 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
XWXin Wang
Xin Wang
KXKaiyuan Xing
Kaiyuan Xing
QLQingyu Li
Qingyu Li
TYTao Yang
Tao Yang

16 July 2024 in Polymers
Verified
Journal Article
Open access
PDF file
TYTao Yang
Tao Yang
CLChanghong Lin
Changhong Lin
MHMin Huang
Min Huang
PYPuyou Ying
Puyou Ying
PZPing Zhang
Ping Zhang
VLVladimir Levchenko
Vladimir Levchenko
With the background of the fossil fuel energy crisis, the development of self-healing and recyclable polymer materials has become a research hotspot. In this work, a kind of cross-linking agent with pendent furan groups was first prepared and then used to produce the Polyurethane elastomer based on Diels–Alder chemistry (EPU–DA). In addition, in order to further enhance the mechanical properties of the elastomer, cellulose nanofibers (CNFs) were added into the Polyurethane system to prepare a series of composites with various contents of CNF (wt% = 0.1~0.7). Herein, the FTIR and DSC were used to confirm structure and thermal reversible character. The tensile test also indicated that the addition of CNF increased the mechanical properties compared to the pure Polyurethane elastomer. Due to their reversible DA covalent bonds, the elastomer and composites were recycled under high-temperature conditions, which extends Polyurethane elastomers’ practical applications. Moreover, damaged coating can also be repaired, endowing this Polyurethane material with good potential for application in the field of metal protection.

24 June 2022 in Vacuum
Verified
Journal Article
Closed access
TYTao Yang
Tao Yang
JWJianbo Wu
Jianbo Wu
MHMin Huang
Min Huang
LZLiu Zhu
Liu Zhu
JWJinfang Wang
Jinfang Wang
VLVladimir Levchenko
Vladimir Levchenko

16 July 2022 in Metals
Verified
Journal Article
Open access
PDF file
PYPuyou Ying
Puyou Ying
CLChanghong Lin
Changhong Lin
ZLZhiyi Liu
Zhiyi Liu
SBSong Bai
Song Bai
VLVladimir Levchenko
Vladimir Levchenko
MLMengjia Li
Mengjia Li
In the present work, different aging treatments were performed to investigate the pre-aging effect on the formation of Ω phase and mechanical properties in Al-Cu-Mg-Ag alloy. The results showed that pre-strain could inhibit the formation of Ω phases, which was detrimental to the alloy strength. Due to the introduction of pre-aging treatment before pre-strain, the adverse effect of pre-strain on the precipitation of the Ω phase was reduced, and the alloy strength was increased by at least 15 MPa. Besides this, increasing the pre-aging temperature promoted the precipitation of Ω phases, inhibited the formation of θ′ phases, and improved the alloy strength. This was because the higher pre-aging temperature promoted more pre-precipitated Ω phases in the pre-aging process, and most of the pre-precipitated Ω phases could be retained and grew in the subsequent aging process. As a result, the tensile strength of the alloy increased from 523 MPa to 540 MPa. In addition, pre-aging with a higher temperature consumed more solute atoms, leading to less residual solute atoms in the matrix. Thus, the adverse effects of pre-strain, which inhibit the formation of clusters by the segregation of solute atoms, were reduced.

9 October 2021 in Coatings
Verified
Journal Article
Open access
PDF file
PZPing Zhang
Ping Zhang
PYPuyou Ying
Puyou Ying
CLChanghong Lin
Changhong Lin
TYTao Yang
Tao Yang
JWJianbo Wu
Jianbo Wu
VLVladimir Levchenko
Vladimir Levchenko
MoS2–Ti coating is a widely used solid lubricant owing to its low friction coefficient. The mechanical and tribological performance of the coating can be further improved via introducing a multilayer structure, which is closely related to the modulation period and significantly affects the properties of the coating. Herein, the effect of two different modulation periods on the mechanical and tribological performance of the MoS2–TiL/MoS2–TiH multilayer coatings (where L and H represent low and high-powered sputtering of the titanium target) was studied. The performance of the coatings was found to depend on modulation periods of single layer thickness and thickness ratio, respectively. When the thickness ratio of MoS2–TiL layer to MoS2–TiH layer was fixed with different number of layers, the adverse effects of the interface outweighed the beneficial effect; thus, the mechanical and tribological performance of the multilayer coatings were improved with an increase in the single layer thickness. When the effect of the multilayer interfaces on the studied coatings was similar with the same number of layers, the MoS2–TiH layer had more impact on the hardness of the MoS2–TiL/MoS2–TiH multilayer coatings, whereas the MoS2–TiL layer substantially affected the adhesion properties, friction behavior and wear resistance. This study can provide a way to regulate coatings with different performance requirements via building different multilayer microstructures.

16 April 2024 in Coatings
Verified
Journal Article
Open access
PDF file
JYJianjian Yu
Jianjian Yu
PZPing Zhang
Ping Zhang
PYPuyou Ying
Puyou Ying
CLChanghong Lin
Changhong Lin
TYTao Yang
Tao Yang
VLVladimir Levchenko
Vladimir Levchenko
Magnetron-sputtered WS2 composite thin films are solid lubricants with excellent performances. However, the low hardness of the WS2 thin films necessitates the further improvement of their wear resistance. For this purpose, an effective strategy is to alternately deposit or code posit WS2 and a hard phase, such as TiB2, to form hard lubricant thin films. Herein, a TiB2 thin film was prepared under the same conditions as those used for depositing the WS2 thin film with a dense structure and excellent tribological properties. Because of the high deposition energy of high-power impulse magnetron sputtering (HiPIMS), the TiB2 thin film possesses a dense structure and leather-like flat surface (hardness = 24.17 GPa). The friction coefficient of the film under different loads ranges between 0.6 and 0.8. The wear rate of the thin film increases with load, mainly because of fatigue wear and abrasive wear. Under high loads, obvious furrow-like wear marks are observed. At different sliding frequencies, except 8 Hz, the friction coefficient of the film ranges from 0.6 to 0.8. The main wear mode is fatigue wear, particularly at increasing sliding frequencies. Although the film possesses a relatively high friction coefficient, its wear resistance is excellent (minimum wear rate = 1.96 × 10−6 mm3/(N·m)).