The purpose of this paper is investigating the characteristics of dynamic contact and dynamic stiffness of the single nut ball screw pair (SNBSP). Then a new sensorless method is proposed to extract the SNBSP dynamic contact stiffness of a mass production CNC machine tool feed system. First of all, the transformation relationship between each coordinate system of SNBSP is established. Secondly, the dynamic model of all ball–raceway contact pairs is established. Based on this, a dynamic contact stiffness model is established. The dynamic contact parameters are obtained by the numerical method. It is found that the influence of screw speed on screw and nut raceway normal force distribution are opposite. This will affect the variations of dynamic contact stiffness. It is also clear that the effect of axial load on dynamic stiffness is significant. Then, an effective method is proposed to estimate the dynamic contact stiffness of a mass production CNC machine tool feed system without any external sensors. The axial force of feed system is estimated by using torque current of servo motor. Current signals can be obtained through FANUC Open CNC API Specifications (FOCAS) library functions, and then dynamic contact stiffness can be calculated through the stiffness model without external sensors. Finally, a feed system dynamic model is built, and the contact model and sensorless stiffness estimating method are verified by experiments in this dynamic system.
In view of the time-varying complexity of the heat source for the ball screw feed system, this paper proposes an adaptive inverse problem-solving method to estimate the time-varying heat source and temperature field of the feed system under working conditions. The feed system includes multiple heat sources, and the rapid change of the moving heat source increases the difficulty of its identification. This paper attempts to develop a numerical calculation method for identifying the heat source by combining the experiment with the optimization algorithm. Firstly, based on the theory of heat transfer, a new dynamic thermal network model was proposed. The temperature data signal and the position signal of the moving nut captured by the sensors are used as input to optimize the solution of the time-varying heat source. Then, based on the data obtained from the experiment, finite element software parametric programming was used to optimize the estimate of the heat source, and the results of the two heat source prediction methods are compared and verified. The other measured temperature points obtained by the experiment were used to compare and verify the inverse method of this numerical calculation, which illustrates the reliability and advantages of the dynamic thermal network combined with the genetic algorithm for the inverse method. The method based on the on-line monitoring of temperature sensors proposed in this paper has a strong application value for heat source and temperature field estimation of complex mechanical structures.
High-speed machining is a key technology for greatly improving productivity and reducing production costs. Angular contact ball bearing is the key component of ball screw feed system. Predictive analysis of bearings thermal behavior is significant to ensure the working accuracy of machine tools. Due to the continuous dynamic changes under actual working conditions, it is difficult to predict and model of the bearings heating characteristics. This paper develops a comprehensive calculation method for predicting the thermodynamic characteristics on high speed feed shaft bearings. Based on quasi-static model and thermal dynamic model, Monte Carlo optimization algorithm is used to inverse the temperature field experimental temperature data. The real heating characteristics of heat source are comprehensively predicted and analyzed, so as to accurately predict the bearing thermal dynamic performances of feed shaft bearings. The research work in this paper lays a strong foundation for the thermal error modeling and thermodynamic analysis of the ball screw feed system of machine tools.
In this study, a novel sensorless method is developed to estimate the friction in a ball screw system using asynchronous experimental data for a worktable position (WP) and the servo motor torque current (SMTC), which is collected by the FOCAS library functions from a FANUC digital control system. The corresponding time stamps are retrieved by a high-resolution performance counter in Windows. The fluctuations in friction over the whole travel distance of the worktable (WTDOW) are analyzed using a piecewise polynomial fitting algorithm to extract the instantaneous average friction value (IAFV) and the friction fluctuating signal (FFS). The IAFVs can describe the effect of the WP and the pitch errors of the shaft on the friction. The FFT results of the FFS show that the friction depends on the rolling tool, the pitch of the shaft and the refeeding of the balls in the ball screw and linear ball rail guides. The experimental results show that the estimated friction can capture the characteristic spectra of the FFS. The effects of the feed velocity and direction, the effects of the WP on the IAFV, and the frequencies and amplitudes of the significant FFT components are discussed. The nonuniform pitch errors of the shaft impact the repeatability of the IAFVs at a given WP. The variations in the mean value of the IAFVs with the feed velocity for tests at a fixed WP show nonconventional Stribeck behavior. These results also demonstrate that the friction force varies with the WP, which is not captured by Stribeck characteristics. This study provides an effective method to evaluate the performance of a ball screw system and to predict the friction in that system without the use of sensors.
In order to solve the problem that the flatness error contour curve of the guideway mounting surface on machine tools can not be intuitive description, a novel method is proposed in this paper. The principle is to divide the measured surface with a certain length into several short surfaces with overlapping region, and the segmented surfaces are measured respectively, then the flatness error contours of the segmented surfaces can be obtained, finally, the segmented flatness error contours are spliced together to reconstruct the flatness error contour of the entire surface. On this basis, the detection instrument is designed, the detection principle is given, the benchmark plate is customized to identify the starting position and ending position of measurement, the reference surface and the measured surface are measured respectively in combination with the detection instrument and the benchmark plate. Then, an algorithm is developed to convert the distance difference between the reference surface and the measured surface into the flatness error contours of segmented surfaces. Next, using the geometric relationship between overlapping region of segmented flatness error contours, an algorithm is studied which can splice these segmented flatness error contours and reconstruct the flatness error contour of the entire surface. Meanwhile, mathematical models of the algorithms are established, and the measurement experiment is carried out. The results demonstrate that this method can reconstruct the flatness error contour of long surface accurately.