This research was conducted to determine the cause, intensity and location of damage (stem, butt end, root collar, root) and the extent of damage to standing trees during felling and processing by an harvester and timber extraction by a forwarder (cut-to-length system). The research was conducted in the central part of the Republic of Croatia in the Management Unit (MU) “Bjelovarska Bilogora” during the thinning of Subcompartment 14b, area of 18.28 ha, in the stand of hornbeam (Carpino betuli—Quercetum roboris fagetosum Rauš 1975), age 70, and of Subcompartment 14c, area of 9.07 ha, in a stand of common beech (Carici pilosae—Fagetum Oberdorfer 1957) aged 79 years. The thinning intensity was 12.13% in Subcompartment 14b and 13.72% in Subcompartment 14c. Field measurements were carried out on sample plots—the first time in 2017 to determine the intensity and characteristics of the damage to standing trees with regard to the cause of the damage (harvester or forwarder), and the second time in 2018 to determine the overall intensity and features of the damage to standing trees after finishing harvesting operations. For all trees remaining in the stand after the harvesting operations, the following were determined: tree species, diameter at breast height (DBH), the position of the tree in the stand depending on the forest traffic infrastructure, and—if damaged—cause of damage, type of damage, the position of damage on the tree, and dimensions of damage. The intensity of the damage was expressed by the ratio of damaged and undamaged trees, with a detailed analysis of bark damage (squeezed-bark damage and peeled-bark injuries). The results of the research indicate the highest prevalence of peeled-bark injuries. In relation to the total number of standing trees, trees with peeled-bark injuries were more represented in Subcompartment 14c (39%) than in Subcompartment 14b (33%). In Subcompartment 14b, the harvester and the forwarder damaged an equal number of trees, while in Subcompartment 14c, the harvester damaged 59% of the damaged trees. In both subcompartments, an average of 83% of (peeled bark) injuries were up to 1.3 m above the ground. In both subcompartments, the most common (67%) were injuries up to 100 cm² in size, for which many authors claim the tree can heal by itself. Given the increasing use of harvester-forwarder systems in deciduous stands and research results that indicate possible damage to standing trees, it is necessary to pay attention to all phases of planning and execution of timber harvesting operations, thus minimising negative effects.

The use of forestry vehicles in mechanised harvesting systems is still the most effective way of timber procurement, and forestry vehicles need to have high mobility to face various terrain conditions. This research gives boundaries of planning timber extraction on sloped terrain with a cable skidder, considering terrain parameters (slope, direction of skidding, cone index), vehicle technical characteristics and load size (5 different loads) relying on sustainability and eco-efficiency. Skidder mobility model was based on connecting two systems: vehicle-terrain (load distribution) and wheel-soil (skidder traction performance) with two mobility parameters: (1) maximal slope during uphill timber extraction by a cable skidder based on its traction performance (gradeability), and (2) maximal slope during downhill timber extraction by a cable skidder when thrust force is equal to zero. Results showed mobility ranges of an empty skidder for slopes between −50% and +80%, skidder with 1 tonne load between −26% and +63%, skidder with 2 tonne load between −30% and +51%, skidder with 3 tonne load between −34% and +39%, skidder with 4 tonne load between −35% and +30% and skidder with 5 tonne load between −41% and +11%.These results serve to improve our understanding of safer, more efficient timber extraction methods on sloped terrain.

Based on the knowledge of the dimensional and mass features of a forwarder, a model was developed to assess its mobility during timber forwarding uphill in a safe and eco-efficient way. The model is based on knowledge of the position of the forwarder’s centre of gravity, its declared payload and the length of the loaded timber, as well as the gradeability for uphill timber forwarding based on the traction characteristics of the vehicle. The model connects two research approaches, (1) vehicle–terrain approach (distribution of axle loads depending on the longitudinal terrain slope) and (2) wheel–soil approach (estimation of the traction characteristics of the forwarder based on the wheel numeric), concerning previous research: (i) underload on the front axle of the vehicle, (ii) overload on the rear axle of the vehicle, (iii) permissible tire load, (iv) minimal soil bearing capacity, (v) wheel slip. Simulation modelling for the assessment of the forwarders’ mobility range during timber forwarding uphill was conducted on an example of an eight-wheel Komatsu 875 forwarder, with a declared payload of 16,000 kg, equipped with 710/45-26.5 tires, for which the position of the centre of gravity was determined by the method of lifting the axle. The results of the distribution of the adhesion load on the front and rear axles of the forwarder indicated that, during timber forwarding of 16,000 kg and 4.82 m long hardwood logs on a terrain slope below 68%, there is no critical unloading on the front bogie axle, nor overloading on the rear bogie axle, i.e., wheel tire overload that could limit forwarder mobility. For the specified range of longitudinal terrain slope, a minimal cone index of 950 kPa for an exemplary forwarder is an environmental factor and was calculated based on the nominal ground pressure of the reference (heavier loaded) rear wheels of the vehicle. The forwarders’ mobility range was determined by the intersection curves of the gradeability (based on forwarders’ traction characteristics at wheel slip of 25% vs. cone index) and the curve of the minimal soil cone index.

Rutting measurements are a significant part of scientific research on the impact of forest vehicles on the forest soils and damage to the forest transport infrastructure. Although photogrammetric methods of measurement or measurements based on LiDAR (light detection and ranging) data are increasingly being used for rutting measurements, the previous research conducted using these methods indicated the challenge of recording water-filled ruts. For this reason, it is necessary to define a reliable method of rutting field measurement in lowland forest stands characterized by a high level of groundwater that fills the ruts shortly after the passage of forest vehicles. This research analyzed the measurement accuracy using a total station and a GNSS RTK device with a CROPOS correction base in relation to the measuring rod that represented the reference method. Based on recorded and processed data, ruts are displayed in two ways: as net and as gross value of rut depth. The analysis of net rutting revealed a statistically significant difference between the calculated rut depths based on measurements with a GNSS RTK device and other methods. On average, the net rutting measured by the GNSS RTK device was 2.86 cm smaller than that of the reference method. When calculating the gross rutting, which consisted of the net rut depth and the bulge height, no statistically significant difference was found between the measurement methods used. Based on this result, the bulge height was also analyzed, and showed a statistically significant difference between the data recorded by the GNSS RTK device and other methods. It can be concluded that measuring the depth of ruts with a total station gives accurate data and represents the optimal modern field measurement method for the same or similar terrain conditions. In contrast, the GNSS RTK device, which constantly gives higher elevation points, can be used to measure gross rutting.

Rad se bavi prikazom metode izračuna planskih cijena pridobivanja drva, koje su predmet javnih nadmetanja u Šumsko gospodarskom društvu »Hercegbosanske šume« d.o.o. Kupres te analizom odstupanja planskih od ugovorenih/ostvarenih cijena usluga pridobi...