Nickel–titanium alloys are the most widely used shape memory alloys due to their outstanding shape memory effect and superelasticity. Additive manufacturing has recently emerged in the fabrication of shape memory alloy but despite substantial advances in powder-based techniques, less attention has been focused on wire-based additive manufacturing. This work reports on the preliminary results for the process-related microstructural and phase transformation changes of Ni-rich nickel–titanium alloy additively manufactured by wire-based electron beam freeform fabrication. To study the feasibility of the process, a simple 10-layer stack structure was successfully built and characterized, exhibiting columnar grains and achieving one-step reversible martensitic–austenitic transformation, thus showing the potential of this additive manufacturing technique for processing shape memory alloys.
Thermal treatments are the main route to achieve improvements in mechanical properties of β-metastable titanium alloys developed for structural applications in automotive and aerospace industries. Therefore, it is of vital importance to determine phase transformation kinetics and mechanisms of nucleation and precipitation during heat treatment of these alloys. In this context, the present paper focuses on the assessment of solid-state transformations in a β-water-quenched Ti-5Al-5Mo-5V-3Cr-1Zr alloy during the early stages of ageing treatment at 500 °C. In situ tracking of transformations was performed using high-energy synchrotron X-ray diffraction. The transformation sequence β + ω → α + α”iso + β is proposed to take place during this stage. Results show that isothermal α” phase precipitates from ω and from spinodal decomposition domains of the β phase, whereas α nucleates from ω, β and also from α” with different morphologies. Isothermal α” is considered to be the regulator of transformation kinetics. Hardness measurements confirm the presence of ω, although this phase was not detected by X-ray diffraction during the in situ treatment.
27 June 2023 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
In a previous study (part I), the deposition of functional single-track and multi-layer Ni-rich NiTi using the electron beam freeform fabrication (EBF3) technique was demonstrated. The processed microstructure consists of columnar millimetre range grains that grow parallel to the build direction. Based on the same parameters of part I, this work successfully deposited a stable multi-track and multi-layer NiTi block. Different heat treatments were applied to modify the superelastic properties of the deposited material. Initially, the solution treatment reduces the chemical inhomogeneity and the thermal stresses that originated during the deposition and cooling. Subsequently, due to ageing, Ni4Ti3 particles precipitate at 350 °C and 450 °C for 1, 6 and 12 h, modified the superelastic behaviour of the deposited NiTi. The differential scanning calorimetry results did not reveal any difference in the martensitic starting temperature between as-built and solution-treated samples. However, a remarkable influence of the ageing temperature was detected: while ageing at 350 °C impacted R-phase starting temperatures, 450 °C altered the martensitic starting one. The superelastic behaviour was evaluated by cycling compression. As-built and solution heat-treated samples presented poor mechanical performance, with about 40% of strain recovered after 10 cycles. The ageing at 350 °C for 1 h led to a maximum measured strain recovery of 72.5% after 10 uniaxial compression cycles up to 860 MPa. This condition also resulted in 3.3% permanent deformation out of 11.3% of the total. This study addressed for the first time the fabrication by the EBF3 technique of a stable multi-track and multi-layer NiTi block besides the importance of heat treating it, demonstrating that this post-treatment improves the superelastic performance of EBF3 fabricated parts.
Functionally Graded Additive Manufacturing (FGAM) offers the potential to create high-performance engineering components with locally optimized material properties. While this technology promises significant advancements, the development of reliable grading strategies for low-alloy steel systems remains insufficiently researched. This study investigates the feasibility of producing functionally graded material (FGM) components using Tandem wire-arc directed energy deposition (T-WA-DED) by precisely controlling wire feed ratios. A baseline was established through various single and tandem-wire reference experiments, including assessments of lead and trail electrode arrangements to ensure process stability. Using ER70 and ER120 filler wires, low-alloy steel gradients were fabricated in both the welding (GW) and build (GB) directions, with lengths of up to 140 mm. The resulting structures were systematically investigated using optical emission spectrometry (OES), optical microscopy (OM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX), complemented by Vickers hardness mappings and tensile tests. Finally, mechanical performance was compared with theoretical predictions based on wire volume fractions and evaluated using regression analysis. The results confirm that functional gradients achieve superior mechanical integrity compared to discrete bimetallic transitions by effectively mitigating stress concentrations at interfacial boundaries. Experimental findings indicate that 8–16 mm welding-direction gradients provide a good balance between yield strength and ductility. Furthermore, the hardness profiles exhibit a reliable linear trend that remains consistent with mathematical prediction models. This study provides a validated predictive framework for low-alloy steel gradients. By successfully correlating localized microstructural evolution with mechanical properties, it enables the reliable integration of FGM components into robust structural design.