Laser directed energy deposition (L-DED) was used to produce samples of the newly patented W360 hot work tool steel by Böhler. The process parameters were optimized to obtain nearly fully dense samples through the production and analysis of single deposited tracks and single layers. Subsequently, bulk samples underwent a hardening heat treatment, consisting of austenitizing, air quenching, and tempering. The samples were analysed in the as-built condition (AB), after quenching (Q) and following tempering cycles (HT) to observe the microstructural evolution. The microstructure was investigated using optical and scanning electron microscopes, energy dispersive X-ray analysis, and X-ray diffraction analysis. Furthermore, the microstructural evolution was analysed with differential scanning calorimetry, while the mechanical response was evaluated through microhardness test. It was found that the AB samples exhibited a dendritic-cellular microstructure with tempered martensite laths. The thermal history of the AB samples was completely modified by the austenitizing treatment followed by quenching, resulting in a fully martensitic Q sample that did not display the typical dendritic-cellular microstructure of the L-DED process. The completion of the heat treatment with tempering cycles revealed the presence of Mo-rich carbides dispersed in a martensitic matrix. The HT samples exhibited a mean microhardness of 634 HV, remaining constant along the entire building direction from the substrate to the last deposited layer, indicating a homogeneous microstructure. This high value, similar to other hot work tool steels such as H13, makes W360 a very promising candidate for tool build and repair purposes. Graphical Abstract
30 March 2026 in Journal of Materials Processing Technology
In the aerospace sector, integrating advanced materials with high mechanical capabilities represents the forefront of material science, especially in the field of rocketry. Bimetallic structures are increasingly used in aerospace applications due to their combination of high strength-to-weight ratio, thermal conductivity, and corrosion resistance. Among these, Inconel-copper (In718-Cu) systems are particularly promising, although large differences in thermophysical and mechanical properties between the two materials can induce residual stresses, cracks, and other interfacial defects, requiring careful process control. This study evaluates the fabrication of In718-Cu structures through Direct Energy Deposition (DED), in which In718 was deposited onto a copper substrate using an innovative deposition strategy. Interface quality and microstructure were characterized by SEM/EDS and X-ray diffraction, whereas the mechanical properties were evaluated by nanoindentation, indentation creep, and tensile testing. The results showed that crack-free samples can be achieved, with strong diffusion bonding at the interface and efficient precipitation strengthening on the copper side already in the as-built condition. A uniform distribution of precipitates and consistent penetration depth were also observed, confirming the effectiveness of the deposition strategy for producing reliable In718-Cu components.
24 October 2025 in The International Journal of Advanced Manufacturing Technology
A novel plasma arc and powder-based Directed Energy Deposition process (DED-Arc-P) demonstrates significant potential for manufacturing high-quality metallic structures. While the process has been validated for steel and titanium alloys, its applicability to aluminum, one of the key industrial metals, remains unexplored. This study is the first to investigate AlSi10Mg processed by DED-Arc-P, focusing on the effect of welding speed and heat input on geometry, process efficiency, porosity, and microstructure to qualify the process for AlSi10Mg. The goal was to establish correlations between process parameters and material properties, and to contribute to the further development of DED-Arc-P. Results demonstrate that increased welding speeds enhance the consistency of layer height and width by minimizing heat input and accumulation. All structures exhibited higher geometric deviations in the bottom region, followed by a stable region, with the stable region achieved earlier at higher speeds due to reduced heat input. The structure produced with the highest speed showed slightly increased porosity (~ 2.7%) compared to the others (~ 2.4%). This was caused by the differences in cooling rates. Pores are primarily situated in the lower regions of all structures, attributed to effective heat dissipation by the substrate plate. The dendrite arm spacing, indicative of microstructure fineness, decreased with reduced welding speeds and higher layers as a result of increased heat accumulation. Additionally, the dendrite growth angle in relation to the build-up direction decreased with higher speeds, attributed to variations in weld pool geometry. SEM and EDS analyses revealed that higher welding speeds refine both the dendritic α-Al structure and eutectic Si particles. Fe-rich intermetallic phases, likely β-Al₅FeSi, were identified in the interdendritic regions.
Functionally Graded Additive Manufacturing (FGAM) offers the potential to create high-performance engineering components with locally optimized material properties. While this technology promises significant advancements, the development of reliable grading strategies for low-alloy steel systems remains insufficiently researched. This study investigates the feasibility of producing functionally graded material (FGM) components using Tandem wire-arc directed energy deposition (T-WA-DED) by precisely controlling wire feed ratios. A baseline was established through various single and tandem-wire reference experiments, including assessments of lead and trail electrode arrangements to ensure process stability. Using ER70 and ER120 filler wires, low-alloy steel gradients were fabricated in both the welding (GW) and build (GB) directions, with lengths of up to 140 mm. The resulting structures were systematically investigated using optical emission spectrometry (OES), optical microscopy (OM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX), complemented by Vickers hardness mappings and tensile tests. Finally, mechanical performance was compared with theoretical predictions based on wire volume fractions and evaluated using regression analysis. The results confirm that functional gradients achieve superior mechanical integrity compared to discrete bimetallic transitions by effectively mitigating stress concentrations at interfacial boundaries. Experimental findings indicate that 8–16 mm welding-direction gradients provide a good balance between yield strength and ductility. Furthermore, the hardness profiles exhibit a reliable linear trend that remains consistent with mathematical prediction models. This study provides a validated predictive framework for low-alloy steel gradients. By successfully correlating localized microstructural evolution with mechanical properties, it enables the reliable integration of FGM components into robust structural design.
Laser-directed energy deposition (L-DED) was used to manufacture samples of the newly developed W360 hot-work tool steel from voestalpine Böhler Edelstahl. Various heat-treatment processes, including austenitising followed by air or water-quenching and tempering, as well as direct tempering, were applied. The as-built and heat-treated conditions were characterised by optical microscopy (OM), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM-EDS), electron backscatter diffraction (EBSD) and X-ray diffraction (XRD), while the microstructural evolution during austenitisation was investigated using a high-temperature microscope (HTM). Hardness measurements were performed to determine the material response. The as-built condition exhibited a hardness of 628 ± 12 HV with no manufacturing cracks. The highest hardness (666 ± 13 HV) was obtained after air-quenching, whereas water-quenching produced 651 ± 14 HV. The rapid cooling of water-quenching, however, led to the formation of macroscopic cracks. The lattice distortion differences identified by XRD and the kernel average misorientation values obtained from EBSD indicated differences between the air and water-quenched conditions. High hardness (622–628 HV) was retained after low-temperature direct tempering, whereas high-temperature tempering resulted in significant softening (487 ± 12 HV). These results suggest that low-temperature direct tempering is a promising post-processing treatment for L-DED W360 tool steel, although additional mechanical testing is required to confirm industrial applicability.