Oily wastewater from shipping waste and marine accidents have seriously polluted the marine environment and brought great harm to human production and health. With the increasing awareness of environmental protection, the treatment of marine oily wastewater has attracted extensive attention from the international community. Marine oily wastewater has various forms and complex components, so its treatment technology faces great challenges. Sources, types, supervision, and treatment of marine oily wastewater are introduced in this paper. The research progress of marine and ship’s oily wastewater treatment technologies in recent years are reviewed from the perspectives of physical treatment, chemical treatment, biological treatment, and combined treatment, respectively. Principles and characteristics of all kinds of technologies were analyzed. In addition, this paper shows that multiple processing technologies used in combination for the purpose of high efficiency, environmental protection, economy, and energy conservation are the future development trend.

The adsorption properties of coexistent Cr(VI) and Cu(II) in mixed solution on magnetic magnetite (Fe₃O₄) nanoparticle were studied in batch experiments. The influences of various factors, such as pH, adsorbent dose, temperature, initial concentration of metal ions, and coexisting ions in water were investigated. At the same time, the adsorption kinetics and adsorption isotherms were studied. The mechanism of adsorption for Cr(VI) and Cu(II) was investigated through the study of surface properties of Fe₃O₄, the presence of ions, and the influence of pH and zeta potential. The results indicate that pH has an influence on adsorption for Cr(VI) and Cu(II), and the optimal pH value for Cr(VI) and Cu(II) adsorption is 4.0. The adsorption efficiency increased with the increase of the adsorbent dose. Temperature under experimental design had no obvious effect. With 2.0 g/dm³ Fe₃O₄, the maximum adsorption capacity for Cr(VI) and Cu(II) reached 8.67 mg/g and 18.61 mg/g in mixed solution of 80 mg/dm³ Cr(VI) and Cu(II), respectively. Phosphorus had some influence on the adsorption for Cr(VI), and other coexisting anions and cations had no influence on the adsorption for Cr(VI) and Cu(II). The adsorption data for Cr(VI) and Cu(II) were nicely fit to the Langmuir adsorption equation and the pseudo-second-order model. As a multifunctional material, nano-Fe₃O₄ exhibited good adsorption performance for coexistent Cr(VI) and Cu(II) and could easily be separated and recovered under magnetic field.

The difficulty of residual sludge dehydration is the major problem in sewage treatment. The reduction of moisture content in sludge can reduce the sludge volume significantly and is conducive to the subsequent disposal of sludge. As an organic polymer flocculant, chitosan (CTS) is widely used in water and waste water treatment. In this study, CTS was used in sludge treatment to improve the sedimentation and dehydration properties of sludge. When treated with CTS, the moisture content of sludge cake decreased from 85.9% to 83.0%, the SV30 decreased to about 1/2, and the sludge volume reduced to 82.9%. Further analysis showed that the zeta potential (ζ-potential) of the sludge changed from negative value to positive value, and the D50 of the sludge was larger than that of the raw sludge. In addition, when the moisture content of the sludge cake was reduced to the lowest, the concentration of extracellular polymeric substances (EPS) and SCOD was the largest and the |ζ| decreased to the lowest. CTS improved the dehydration and sedimentation performance of sludge mainly by factors of electrical neutralization, adsorption bridging and dissolution of EPS.

In this study, a catalytic persulfate oxidation process comprising sodium persulfate (PS) and modified sewage sludge-derived carbonaceous catalysts was tested for the degradation of phenol. Sludge-based biochar was modified by high-temperature treatment combined with hydrochloric acid oxidation. The surface properties of carbonaceous catalysts before and after modification were characterized by elemental analysis, N₂ isothermal adsorption-desorption, scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The effects of reaction parameters including catalyst dosage, PS/phenol molar ratio, initial pH and reaction temperature on the degradation rate of phenol were investigated. The kinetics of phenol transformation was explored and the reaction rate appeared pseudo first-order kinetics. In SS-600-HCl/PS system, 91% phenol could be efficiently degraded under certain reaction conditions ([phenol]₀ = 100 mg/L, catalyst dosage = 0.8 g/L, PS/phenol molar ratio = 3/1, pH = 7, 25 °C) in 180 min. Thus, the results showed that the modified sewage sludge-derived carbonaceous catalyst had a better ability to activate PS for phenol degradation.

The removal of oil contaminants in marine intertidal sediments under cold climate is an urgent issue. Although the bioavailability of petroleum hydrocarbons decreases at low temperatures, biosurfactants can promote oil biodegradation. In this study, characteristics of biosurfactants produced by cold-adapted oil-degrading bacteria Planococcus sp. XW-1 were studied. Adding the XW-1 biosurfactant could effectively facilitate the solubility of phenanthrene, pyrene, diesel oil, and crude oil. The solubilization was limited by the number of rings and the molecular weight (WSRphenanthrene = 0.0234; WSRpyrene = 0.0165; WSRdiesel oil = 0.0027; WSRcrude oil = 0.0015). Additional biosurfactants significantly washed out crude oil adsorbed to the sand (reduction from 17.1%, 22.7% to 87.9% and 94.28% in 24 h). With the increase in particle size, the removal efficiency increased from 87.9% to 94.28%. After the addition of biosurfactant, the effect of degradation increased by 20% in 20 days. The results suggest that the biosurfactant-producing bacteria Planococcus sp. XW-1 is a promising candidate used in the in situ bioremediation of petroleum-contaminated intertidal sediment.