Biodegradable triblock copolymers based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were synthesized via ring-opening polymerization of L-lactide followed by reversible addition–fragmentation chain-transfer (RAFT) polymerization of poly(methyl vinyl ketone) (PMVK) as a photodegradable block, and characterized by FT-IR and ¹H NMR spectroscopy for structural analyses, and by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) for their thermal properties. Porous, biodegradable PCL-b-PLA microspheres were fabricated via the oil/water (O/W) emulsion evaporation method, followed by photodegradation of PMVK blocks by UV irradiation. The macro-chain transfer agent (CTA) synthesized by reacting a carboxylic-acid-terminated CTA—S-1-dodecyl-S′-(a,a′-dimethyl-a′′-acetic acid)trithiocarbonate (DDMAT)—with a hydroxyl-terminated PCL-b-PLA block copolymer was used to synthesize well-defined triblock copolymers with methyl vinyl ketone via RAFT polymerization with controlled molecular weights and narrow polydispersity. Gel permeation chromatography traces indicated that the molecular weight of the triblock copolymer decreased with UV irradiation time because of the photodegradation of the PMVK blocks. The morphology of the microspheres before and after UV irradiation was investigated using SEM and videos of three-dimensional confocal laser microscopy, showing a change in their surface texture from smooth to rough, with high porosity owing to the photodegradation of the PMVK blocks to become porous templates.

Epoxy resins are commonly used to manufacture the molding compounds, reinforced plastics, coatings, or adhesives required in various industries. However, the demand for new epoxy resins has increased to satisfy diverse industrial requirements such as enhanced mechanical properties, thermal stability, or electrical properties. Therefore, in this study, we synthesized new epoxy resin (PPME) by modifying phosphorous-containing polyol. The prepared resin was analyzed and added to epoxy compositions in various quantities. The compositions were cured at high temperatures to obtain plastics to further test the mechanical and thermal properties of the epoxy resin. The measured tensile and flexural strength of epoxy compositions were similar to the composition without synthesized epoxy resin. However, the heat release rates of the compositions exhibited tendencies of a decrease proportional to the amount of PPME.

The reversible addition–fragmentation chain transfer (RAFT) emulsion polymerization of diethyl-(4-vinylbenzyl) phosphate (DEVBP) was performed using PEG-TTC as a macro RAFT agent. PEG-TTC (M_W 2000, 4000) was synthesized by the esterification of poly (ethylene glycol) methyl ether with a carboxylic-terminated RAFT agent, composed a hydrophilic poly (ethylene glycol) (PEG) block and a hydrophobic dodecyl chain. The RAFT emulsion polymerization of DEVBP was well–controlled with a narrow molecular size distribution. Dynamic light scattering and confocal laser scanning microscopy were used to examine the PEG-b-PDVBP submicron particles, and the length of the PEG chain (hydrophilic block) was found to affect the particle size distribution and molecular weight distribution. The submicron particle size increased with increasing degree of polymerization (35, 65, and 130), and precipitation was observed at a high degree of polymerization (DP) using low molecular weight PEG-TTC (DP 130, A3). The flame retardant properties of the PEG-b-PDVBP were evaluated by thermogravimetric analysis (TGA) and micro cone calorimeter (MCC). In the combustion process, the residue of PEG-b-PDEVBP were above 500 °C was observed (A1 ~ B3, 27 ~ 38%), and flame retardant effect of PEG-b-PDEVBP submicron particles/PVA composite were confirmed by increasing range of temperature and decreasing total heat release with increasing contents of PEG-b-PDEVBP. The PEG-b-PDEVBP submicron particles can provide flame retardant properties to aqueous, dispersion and emulsion formed organic/polymer products.