Increasing the power conversion efficiency of silicon (Si) photovoltaics is a key enabler for continued reductions in the cost of solar electricity. Here, we describe a two-terminal perovskite/Si tandem design that increases the Si cell’s output in the simplest possible manner: by placing a perovskite cell directly on top of the Si bottom cell. The advantageous omission of a conventional interlayer eliminates both optical losses and processing steps and is enabled by the low contact resistivity attainable between n-type TiO2 and Si, established here using atomic layer deposition. We fabricated proof-of-concept perovskite/Si tandems on both homojunction and passivating contact heterojunction Si cells to demonstrate the broad applicability of the interlayer-free concept. Stabilized efficiencies of 22.9 and 24.1% were obtained for the homojunction and passivating contact heterojunction tandems, respectively, which could be readily improved by reducing optical losses elsewhere in the device. This work highlights the potential of emerging perovskite photovoltaics to enable low-cost, high-efficiency tandem devices through straightforward integration with commercially relevant Si solar cells.
Graphene supported transition metal clusters are of great interest for potential applications, such as catalysis, due to their unique properties. In this work, a simple approach to deposit Au101(PPh3)21Cl5 (Au101NC) on reduced graphene oxide (rGO) via an ex situ method is presented. Reduction of graphene oxide at native pH (pH ≈ 2) to rGO was performed under aqueous hydrothermal conditions. Decoration of rGO sheets with controlled content of 5 wt% Au was accomplished using only pre-synthesised Au101NC and rGO as precursors and methanol as solvent. High resolution scanning transmission electron microscopy indicated that the cluster size did not change upon deposition with an average diameter of 1.4 ± 0.4 nm. It was determined that the rGO reduction method was crucial to avoid agglomeration, with rGO reduced at pH ≈ 11 resulting in agglomeration. X-ray photoelectron spectroscopy was used to confirm the deposition of Au101NCs and show the presence of triphenyl phosphine ligands, which together with attenuated total reflectance Fourier transform infrared spectroscopy, advocates that the deposition of Au101NCs onto the surface of rGO was facilitated via non-covalent interactions with the phenyl groups of the ligands. Inductively coupled plasma mass spectrometry and thermogravimetric analysis were used to determine the gold loading and both agree with a gold loading of ca. 4.8–5 wt%. The presented simple and mild strategy demonstrates that good compatibility between size-specific phosphine protected gold clusters and rGO can prevent aggregation of the metal clusters. This work contributes towards producing an agglomeration-free synthesis of size-specific ligated gold clusters on rGO that could have wide range of applications.
Compact self-assembled monolayers (SAMs) of perfluorododecyl iodide (I-PFC12) of reproducible thickness (1.2 nm) are shown to form on silicon wafers. The SAMs have a high fluorine content (95%) and convey an extremely low surface energy to the silicon wafers (4.3 mN m−1), lower than previously reported in the literature for perfluorinated monolayers, and stable for over eight weeks. Shorter chain iodo-perfluorinated (I-PFC8) or bromo-perfluorinated molecules (Br-PFC10) led to less dense layers. The monolayers are stable to heating up to 60 °C, with some loss up to 150 °C. The I-PFC12 monolayer increases the work function of silicon wafers from 3.6 V to 4.4 eV, a factor that could be gainfully used in photovoltaic applications. The I-PFC12 monolayers can be transferred into patterns onto silica substrates by micro-contact printing. The NMR data and the reproducible thickness point to an upright halogen bonding interaction between the iodine in I-PFC12 and the surface oxygen on the native silica layer.
30 December 2022 in Solar Energy Materials and Solar Cells
Stoichiometry anisotropy through the thickness of the promising photovoltaic material Cesium-lead-bromide (CsPbBr3) is observed, impacting the energy band levels and work function across the thin film.