The present work studies the possibility of energy recovery by thermal conversion of combustible residual materials, namely tires and rubber-plastic, plastic waste from outdoor luminaires. The waste has great potential for energy recovery (HHV: 38.6 MJ/kg for tires and 31.6 MJ/kg for plastic). Considering the thermal conversion difficulties of these residues, four co-combustion tests with mixtures of tires/plastics + pelletized Miscanthus, and an additional test with 100% Miscanthus were performed. The temperature was increased to the maximum allowed by the equipment, about 500 °C. The water temperature at the boiler outlet and the water flow were controlled (60 °C and 11 L/min). Different mixtures of residues (0–60% tires/plastics) were tested and compared in terms of power and gaseous emissions. Results indicate that energy production increased with the increase of tire residue in the mixture, reaching a maximum of 157 kW for 40% of miscanthus and 60% of tires. However, the automatic feeding difficulties of the boiler also increased, requiring constant operator intervention. As for plastic and rubber waste, fuel consumption generally decreased with increasing percentages of these materials in the blend, with temperatures ranging from 383 °C to 411 °C. Power also decreased by including such wastes (66–100 kW) due to feeding difficulties and cinder-fusing problems related to ash melting. From the study, it can be concluded that co-combustion is a suitable technology for the recovery of waste tires, but operational problems arise with high levels of residues in the mixture. Increasing pollutant emissions and the need for pre-treatments are other limiting factors. In this sense, the thermal gasification process was tested with the same residues and the same percentages of mixtures used in the co-combustion tests. The gasification tests were performed in a downdraft reactor at temperatures above 800 °C. Each test started with 100% acacia chip for reference (like the previous miscanthus), and then with mixtures of 0–60% of tires and blends of plastics and rubbers. Results obtained for the two residues demonstrated the viability of the technology, however, with mixtures higher than 40% it was very difficult to develop a process under stable conditions. The optimum condition for producing a synthesis gas with a substantial heating value occurred with mixtures of 20% of polymeric wastes, which resulted in gases with a calorific value of 3.64 MJ/Nm³ for tires and 3.09 MJ/Nm³ for plastics and rubbers.

This study investigates the thermochemical decomposition and gasification performance of biochars produced from blends of waste lignocellulosic biomass and waste insulation electrical cables at varying temperatures. Characterization tests revealed changes, particularly in ash content (27.5 %–34 %) and elemental composition, with nitrogen content increasing notably in biochar samples compared to the original feedstock. Van Krevelen diagrams demonstrated a reduction in O/C and H/C ratios with increasing production temperature, resembling fossil fuels more closely. The thermogravimetric and the derived thermogravimetric profiles illustrated distinct degradation stages influenced by heating rates and production temperature. Macro-TGA tests provided insights into biomass residue behavior under gasification conditions, indicating higher reaction rates at elevated temperatures. Syngas analysis highlighted the impact of temperature and equivalence ratio on syngas composition, with higher temperatures favoring hydrogen-rich gas production. The observed trends in cold gas efficiency (42.61 %–50.40 %) and carbon conversion efficiency (45.83 %–50.40 %) underscore the significance of temperature control in maximizing gasification performance. Biochars produced at higher temperatures demonstrated superior gasification performance, suggesting potential for optimizing biochar production processes to enhance energy recovery and waste valorization.

The recovery of urban waste is a social demand and a measure of the energy-environmental sustainability of cities and regions. In particular, waste of electrical origin, waste of electrical and electronic materials (WEEE) can be recovered with great success. The plastic fraction of these wastes allows their gasification mixed with biomass, and the results allow for producing syngas with a higher energy potential. This work allows for obtaining energy from the recovery of obsolete materials through thermochemical conversion processes of the plastic waste from the disassembly of the luminaires by mixing the said plastic waste in different proportions with the biomass of crop residues (olive). The gasification tests of these mixtures were carried out in a downstream fixed-bed drown daft reactor, at temperatures of approximately 800 °C. The results demonstrate the applied technical and economic feasibility of the technology by thermal gasification, for the production of LHV (Low Heating Value) syngas with highest power energy (more than 5 MJ/m³) produced in mixtures of up to 20% of plastic waste. This study was complemented with the economic-financial analysis. This research can be used as a case study for the energy recovery through gasification processes of plastic waste from luminaires (WEEE), mixed with agricultural biomass that is planned to be carried out on a large scale in the Alentejo (Portugal), as a solution applied in circular economy strategies.

The present study evaluates the digestion of cork boiling wastewater (CBW) through a biochemical methane potential (BMP) test. BMP assays were carried out with a working volume of 600 mL at a constant mesophilic temperature (35 °C). The experiment bottles contained CBW and inoculum (digested sludge from a wastewater treatment plant (WWTP)), with a ratio of inoculum/substrate (Ino/CBW) of 1:1 and 2:1 on the basis of volatile solids (VSs); the codigestion with food waste (FW) had a ratio of 2/0.7:0.3 (Ino/CBW:FW) and the codigestion with cow manure (CM) had a ratio of 2/0.5:0.5 (Ino/CBW:CM). Biogas and methane production was proportional to the inoculum substrate ratio (ISR) used. BMP tests have proved to be valuable for inferring the adequacy of anaerobic digestion to treat wastewater from the cork industry. The results indicate that the biomethane potential of CBWs for Ino/CBW ratios 1:1 and 2:1 is very low compared to other organic substrates. For the codigestion tests, the test with the Ino/CBW:CM ratio of 2/0.7:0.3 showed better biomethane yields, being in the expected values. This demonstrated that it is possible to perform the anaerobic digestion (AD) of CBW using a cosubstrate to increase biogas production and biomethane and to improve the quality of the final digestate.