In this paper, the strength and deformation failure characteristics of bearing coal rock mass are related to the confining pressure, and the SAS-2000 experimental system is used to carry out uniaxial and 3, 6, and 9 MPa triaxial tests on coal rock to assess the strength and deformation failure characteristics of coal rock under different confining pressure conditions. The results show that the stress–strain curve of coal rock undergoes four evolutionary stages after fracture: compaction, elasticity, plasticity, and rupture. With confining pressure, the peak strength of coal rock increases, and the elastic modulus increases nonlinearly. The coal sample changes more with confining pressure, and the elastic modulus is generally smaller than that of fine sandstone. The stage of evolution under confining pressure constitutes the failure process of coal rock, with the stress of different evolution stages causing various degrees of damage to coal rock. In the initial compaction stage, the unique pore structure of the coal sample makes the confining pressure effect more apparent; the confining pressure makes the bearing capacity of the coal rock plastic stage stronger, the residual strength of the coal sample has a linear relationship with the confining pressure, and the residual strength of the fine sandstone has a nonlinear relationship with the confining pressure. Changing the confining pressure state will cause the two kinds of coal rock samples to change from brittle failure to plastic failure. Different coal rocks under uniaxial compression experience more brittle failure, and the overall degree of crushing is higher. The coal sample in the triaxial state experiences predominantly ductile fracture. The whole is relatively complete after failure as a shear failure occurs. The fine sandstone specimen experiences brittle failure. The degree of failure is low, and the confining pressure’s effect on the coal sample is obvious.
1 January 2021 in Advances in Materials Science and Engineering
The existing research data show that, after reservoir impoundment, due to the repeated rise and fall of water level and water‐rock interaction, the mechanical parameters of landslide are reduced, which will have an adverse effect on the stability of landslide. Therefore, sufficient attention must be paid to the stability of slope after reservoir impoundment. Hejia landslide is the largest landslide near the bank of Miaojiaba hydropower station, and its stability plays an important role in the normal operation of the hydropower station. Through field investigation and analysis of regional geological conditions, it is concluded that Hejia landslide is a large‐scale landslide, through long‐term sliding‐bending deformation; it is generated from the external hard rock with thick layers and sliding zone for layered soft rock; the formation mechanism of landslide is as follows: (1) high‐steep and hard‐soft layered slope is the slope structure condition that caused the large landslide; (2) the existence of thick soft rock belt provides material conditions for the formation of slip surface; (3) certain air conditions provide displacement space for the separation and disintegration of the sliding body, and the landslide is stable at present. Numerical analysis results show that reservoir impoundment will adversely affect the stability of landslide. In order to ensure the normal operation of power station, certain engineering measures must be taken to treat Hejia landslide. After taking measures, years of monitoring data show that the deformation of Hejia landslide tends to be stable, and the current operation is normal, indicating that the engineering treatment measures are reasonable and feasible.
When carrying out construction that underpasses existing subway tunnels, the surrounding rock is frequently disturbed. Therefore, it can loosen easily and become unstable, which makes its stability difficult to control. Here, we considered an existing subway tunnel in a certain subway section and used orthogonal experiments to design a simulation program as well as the UDEC (Universal Distinct Element Code) simulation software to determine the influences of four factors (i.e., grout density, grouting pressure, dynamic shear force, and viscosity) on the grouting reinforcement effect. The following results were obtained: (1) the combination of the construction method and the grouting parameters strongly influences the reinforcement effect on the surrounding rock of the tunnel. The grouting pressure is not directly proportional to the stability of the surrounding rock. The dynamic adjustment of the relationship between the grouting pressure and the grout density can effectively improve the stress state of the surrounding rock of the tunnel, control surface settlement and deformation, and reduce the section reduction rate of the tunnel. (2) The distribution of joints is closely related to the failure area and form of the surrounding rock of the tunnel. For surrounding rock with well‐developed joint fissures, an excessively high grouting pressure should not be used as they are unstable. (3) The effective bearing range of grouting‐reinforced surrounding rock is dependent on the pore pressure and principal stress difference. The area where the pore pressure is 70–80% of the initial grouting pressure is the effective bearing range of the grouting‐reinforced surrounding rock. The stability of the surrounding rock increases with decreasing principal stress difference and increasing range. (4) The actual monitored data show that the surface settlement can be effectively reduced by handling of grouting reinforcement parameters flexibly, which can meet the control standards.
The quality of excavated and unloaded rock masses on steep and high slopes in cold regions is prone to deterioration, which in turn affects the long-term stability and safety of excavated slopes. Based on a triaxial unloading-damage test of sandstone, the unloading quantity was used to analyze the evolution law of unloading damage; a freeze-thaw cycle test of the unloaded-damaged samples was carried out, and it was found that the average change in porosity and the reloading peak strength damage rate after freeze-thaw increased with the increase in the number of freeze-thaw cycles, and the porosity change characteristics were independent of the value of the confining pressure at the time of the unloading damage. An exponential decay model was used, and based on the average change in porosity after freeze-thaw, a freeze-thaw strength decay model that can take into account the effect of confining pressure was established, and its ability to predict the strength decay of unloaded-damaged rock samples after freeze-thaw was verified by experimental data. The research results provide a reference for the evaluation of freeze-thaw degradation of unloaded rock masses during slope excavation in cold regions.