In this paper, the interactions between two parallel cracks are investigated experimentally and numerically. Finite element models have been established to obtain the stress intensity factors and stress distributions of the parallel cracks with different positions and sizes. Fatigue crack growth tests of 304 stainless steel specimens with the single crack and two parallel cracks have been conducted to confirm the numerical results. The numerical analysis results indicate that the interactions between the two parallel cracks have an enhancement or shielding effect on the stress intensity factors, depending on the relative positions of the cracks. The criterion diagram to determine the enhancement or shielding effect between two parallel cracks is obtained. The changes of the stress fields around the cracks have been studied to explain the mechanism of crack interactions.
In this paper, the interactions between double cracks with a co-bisector-line were investigated theoretically and experimentally. Fatigue crack growth tests of specimens with a single crack or double cracks were carried out to measure the crack growth rates, and finite element calculations were performed to obtain the stress intensity factors at crack tips. It was found that when the double cracks are in co-bisector-line, they present shielding interactions which reduce the stress intensity factors at crack tips as well as the crack growth rates. By modifying the stress intensity factors and the Paris equation considering the shielding interactions, a new simplification method was proposed to simplify the double cracks into a single crack with the same crack growth rates.
In this paper, the fatigue crack growth behavior of the base metal (BM), the weld metal (WM) and the heat-affected zone (HAZ) in the metal-inert gas (MIG) welded joints of the 06Cr19Ni10 stainless steel are analyzed and studied. Results of the fatigue crack propagation tests show that a new fatigue crack initiates at the crack tip of a pre-existing crack, then propagates perpendicular to the direction of cyclic fatigue loads. This observation indicates that the original mixed-mode crack transforms into the mode I crack. The WM specimen has the largest fatigue crack growth rate, followed by the HAZ specimen and the BM specimen. To illustrate the differences in fatigue crack growth behavior of the three different types of specimens, metallographic structure, fracture morphology and residual stresses of the BM, HAZ and WM are investigated and discussed. The metallographic observations indicate that the mean grain size of the HAZ is relatively larger than that of the BM. The fractographic analysis shows that the WM has the largest fatigue striation width, followed by the HAZ and the BM. It is also found that the depth of dimple in the WM is relatively shallower than the one in the HAZ and BM, implying the poor plasticity behavior of the material. Analysis results of the residual stress analysis demonstrate a high level of tensile residual stress appearance in the WM and HAZ.
In this paper, interactions of double parallel cracks were studied by performing experiments and numerical simulations. Fatigue crack propagation tests were carried out to measure crack growth rates in the specimens with double parallel cracks or a single crack. Finite element method was adopted to calculate stress intensity factors at the crack tips. Results show that the double parallel cracks at different positions present a shielding effect or enhancement effect on crack growth rates and stress intensity factors. When the double parallel cracks are offset, crack interactions mostly behave as enhancement effects. Empirical formulas were obtained to calculate the stress intensity factor at the “dangerous” crack tip of the double parallel cracks. By modifying the material parameters in Paris equation of the single crack, the double parallel cracks are simplified into a single crack with the same crack growth rates.
1 September 2025 in Journal of Physics: Conference Series
During the routine inspections of nuclear stations, vibration pipes are often detected. Nonlinear energy sink (NES), a type of nonlinear vibration absorber, exhibits an excellent vibration control capability across a broad range of frequencies. Therefore, this paper has analyzed the applicability of NES for vibration pipes in nuclear stations. Dynamic model of pipes with fluid has been established. Intrinsic frequency and vibration amplitude of pipes have been obtained. Then, for the centralized installation and distributed installation, the vibration amplitude of pipes installed the NES with limited amplitude of the oscillator has been obtained, and vibration control capability for the two combined installation methods has been analyzed. Finally, two NES have been installed on a vibration pipe in a nuclear station. Results demonstrated that combined installation of the NES effectively reduces vibration across broadband frequencies.