Mining high-gas coal seams in China has the characteristics mining of deep, high storage and low permeability, and low drainage efficiency, which seriously restrict the efficient prevention and control of mine gas disasters. Based on the characteristics of low viscosity and permeability, phase change pressurization, and strong adsorption potential energy of liquid CO₂, the technology system of liquid CO₂ displacement for high-gas and low-permeability coal seam was developed, and field industrial of low-pressure (0.52.5MPa) and medium-pressure (2.515.0MPa) combined injection test was carried out. In this test, the mode of injection followed by drainage was adopted, and the gas drainage effect was investigated for 30 days. The test results show that the effective influence radius of CO₂ in this test is 20m, and the liquid seepage radius is 5 to 7m. After the injection of liquid CO₂ into coal seam, the average gas drainage concentration and drainage purity of all drainage holes were increased by 3.2 and 3.4 times, respectively, and the gas promotion effect was significant. Taking the liquid CO₂ low-medium-pressure displacement gas test area as the calculation unit, from the comprehensive benefit analysis, compared with the original drainage mode, the liquid CO₂-combined pressure injection process can save 34.7 of the engineering cost and shorten the gas drainage standard time by 45.9. Therefore, the application of this technology has important technical support and reference significance for the efficient management of gas in the same type of mine.

High-temperature poisonous smoke produced by coal mine roadway fire seriously affects miners' lives and safety. Studying the development law of high-temperature smoke in the process of mine roadway fire and then exploring the danger of roadway are of great significance to personnel safety and post-disaster rescue. In order to study this problem, the CFD numerical simulation method is used to establish a fire calculation model based on ANSYS Fluent software in the development stage of mine fire. The high-temperature flue gas flow in the roadway during the development stage of mine fire is simulated, and the variation law of temperature field and gas concentration field with time and space position under different levels of roadway in the development stage of fire is revealed. The variation rules of environmental parameters, such as temperature, CO, and CO₂, are obtained by numerical calculation. Based on these, the danger zones of smoke spread in fire development stage are divided by the critical values of high-temperature smoke and toxicity evaluation index, and the mathematical fitting analysis of the evolution of the dangerous area with time is carried out. The research results have certain theoretical guiding significance for reducing underground environmental pollution and ensuring the personal safety of workers and rescuers.

Coal mine gas disasters have severely restricted production safety. Improving gas extraction efficiency can effectively reduce disasters. Scholars have confirmed that CO₂ successfully displaces coal seam CH₄. This study conducted displacement and in situ experiments and compared gas drainage under different injection pressures. The displacement experiments indicated that CH₄ production rates increased under increased pressures while the displacement ratios decreased. The pressure had a positive effect on sweep efficiency. The in situ experiment showed that CH₄ and CO₂ concentration trends in the inspection hole remained consistent. Through observing the data of the original and inspection holes, the average gas drainage concentration during low- and medium-pressure injections increased by 0.61 times and 1.17 times, respectively. The low-pressure average gas drainage scalar was increased by 1.08 times. During the medium-pressure injection, the average gas drainage purity increased by 1.94 times. The diffusion ranges of CO₂ under low- and medium-pressure injections were 20–25 m and 25–30 m, respectively. The sweep efficiency of medium-pressure injection was 26% better than that of the low-pressure injection, with average pressures of 2.8 MPa and 1.4 MPa, respectively, for sweep efficiency. This study proposes an effective method for improving coal mine gas drainage efficiency.

Power ultrasonic-assisted reservoir modification is a promising technique for enhanced coalbed methane recovery. However, the in-site performance of ultrasound-assisted CBM production has not yet been revealed. In the current study, the in situ antireflection test was conducted with high-power ultrasound ~18 kW in underground coal seam, and the antireflection performance was investigated by measuring the borehole drainage gas data in the field test zone, and then, the in situ permeability change of the target coal seam was evaluated numerically. The result shows that, within 40 days’ drainage after ultrasonic antireflection in coal seam, the average gas concentration of single borehole in the experimental group increased by 81.4 %~227.3% than that in control group, the average borehole gas flowrate has a 20%~106% improvement over the control group, and the pure methane production in single borehole increased by about 3.83 times. The permeability inversion indicates that the in situ coal seam permeability has increased by at least 2.36 times after the ultrasound stimulation within the range of 8 m from the ultrasound source.

The characteristic parameter test is the basis for the prevention and control of the spontaneous combustion of coal; however, there are some deficiencies in many test methods at present, such as large amounts of experimental coal, long testing periods, and not being able to fully reflect the oxidation and exothermic characteristics of coal itself. This study has independently designed and developed a test device to determine the characteristic parameters of the spontaneous combustion of coal based on the isothermal difference leading method. Through experimental testing of different coal samples using 3, 7, 10, 15, and 20°C as the leading values, it was determined that the lead error was less affected by the lead value, and that it had a direct relationship with the temperature control program. The difference in the lead value did not change the linearity; however, it changed the periodicity. The optimal leading temperature difference was determined as 15°C. In a comparison experiment using a large-scale spontaneous combustion test bench, the heating law of the spontaneous combustion of coal was consistent. The experimental system based on isothermal difference leading achieved the adiabatic oxidation of coal up to a maximum point, which could better reflect the low-temperature oxidization of coal, reduce the amount of experimental coal needed, and improve the experimental periodicity. Additionally, it considerably improved experimental efficiency and provided a new technical approach for the prevention and control of the spontaneous combustion of coal.