Rapid increase in operating frequencies and power density necessitate the importance of examining electromagnetic compatibility/electromagnetic emissions (EMEs) from high-frequency and high-power integrated circuits (ICs). In this paper, a simulation method is demonstrated to study the EME using gallium nitride high electron mobility transistor power amplifier IC chip as a device under test. Simulation model is developed by collaborating a high-frequency structure simulator with a Keysight Advance Design System for simulation of three-dimensional layout of IC. The simulated EME results are verified with experimental measurement results; the hotspots obtained with higher EME as identified by a near-field scanner and simulation results are identical. With this simulation method, optimization is done using a response surface methodology to reduce the EME for the IC chip. It is found that small changes in the IC layout can make a significant difference in the EME. Simulation model developed with RSM optimization technique opens a gateway for the IC industry to investigate EME of their chip design without going through a costly and time-consuming process of fabrication for testing its EME.
A printed circuit board (PCB) is an essential element for practical circuit applications and its failure can inflict large financial costs and even safety concerns, especially if the PCB failure occurs prematurely and unexpectedly. Understanding the failure modes and even the failure mechanisms of a PCB failure are not sufficient to ensure the same failure will not occur again in subsequent operations with different batches of PCBs. The identification of the root cause is crucial to prevent the reoccurrence of the same failure. In this work, a step-by-step approach from customer returned and inventory reproduced boards to the root cause identification is described for an actual industry case where the failure is a PCB burn-out. The failure mechanism is found to be a conductive anodic filament (CAF) even though the PCB is CAF-resistant. The root cause is due to PCB de-penalization. A reliability verification to assure the effectiveness of the corrective action according to the identified root cause is shown to complete the case study. This work shows that a CAF-resistant PCB does not necessarily guarantee no CAF and PCB processes can render its CAF resistance ineffective.
31 July 2019 in IEEE Transactions on Industrial Electronics
Owing to the high frequency and high power requirements for communication integrated circuits (ICs) in today rapid development of electronic technology, the intensity of electromagnetic field from the ICs can be significant. This work shows a failure due to this enhanced electromagnetic field in a Gallium Nitride based High Electron Mobility Transistor (GaN-HEMT) high frequency power amplifier. Inputs were provided as per the rated values and failures are observed on the drain and gate terminals. Detail failure analysis on the failed samples, using focus ion beam (FIB) technique for cross sectioning the damaged area and examining under scanning electron microscopy/ energy dispersive X-Ray spectroscopy (SEM/EDS), reveals the meltdown of the materials at the drain and gate terminals. Electromagnetic simulations and measurements are performed, and the failure mechanism is confirmed to be due to the magnetic field induced eddy current in the drain metal plate of the transistor, on top of the designed operating current in the metal plate.
Advancements in the functionalities and operating frequencies of integrated circuits (IC) have led to the necessity of measuring their electromagnetic Interference (EMI). Three-dimensional integrated circuit (3D-IC) represents the current advancements for multi-functionalities, high speed, high performance, and low-power IC technology. While the thermal challenges of 3D-IC have been studied extensively, the influence of EMI among the stacked dies has not been investigated. With the decreasing spacing between the stacked dies, this EMI can become more severe. This work demonstrates the potential of EMI within a 3D-IC numerically, and determines the minimum distance between stack dies to reduce the impact of EMI from one another before they are fabricated. The limitations of using near field measurement for the EMI study in stacked dies 3D-IC are also illustrated.
Electromagnetic compatibility (EMC) analysis is mandatory due to the rapid increase in operating frequencies, RF interference and PCB layout density. Testing of IC layout is gaining importance as the electromagnetic interference (EMI) issues are increasingly problematic for an IC designer, and even becoming a critical factor for determining the performance of circuits at chip level. However, EMC/EMI testing is not reported at the IC on design level, and currently, for the EMC/EMI study on IC, chips are designed, fabricated and then tested for EMC/EMI and this is after the fact, and can be very costly and time consuming, especially for chips that operate at very high frequency. Hence, there is a great need for evaluating the EMC/EMI of IC at design level. In this work, a design methodology is demonstrated at IC design level by verifying its EMI. A Physically Unclonable Functions (PUF) IC chip is chosen for demonstration. The simulation results of its EMI spectrum using ADS software is verified experimentally using IC EMI scanner. Both IC-Scanner and ADS results agree well and they verify that the maximum noise-radiation peak is observed at a frequency of 17 MHz. The area and location of the maximum noise radiation are located in this work through the simulation.
14 November 2019 in Journal of Materials Chemistry C