The Internet of Things (IoT) has a great number of sensor nodes distributed in different environments, and the traditional approach uses batteries to power these nodes: however, the resultant huge cost of battery replacement means that the battery-powered approach is not the optimal solution. Micro energy harvesting offers the possibility of self-powered sensor nodes. This paper provides an overview of energy harvesting technology, and describes the methods for extracting energy from various sources, including photovoltaic, thermoelectric, piezoelectric, and RF; in addition, the characteristics of the four types of energy sources and the applicable circuit structures are summarized. This paper gives the pros and cons of the circuits, and future directions. The design challenges are the efficiency and size of the circuit. MPPT, as an important method of improving the system efficiency, is also highlighted and compared.
The combination of blockchain and internet of things (IoT) technology realizes reliable storage of IoT data. However, the data stored on the blockchain (on-chain) face the problem of poor scalability and inefficient retrieval. In this paper, the on-chain data scalability schemes based on transactions and smart contracts are first proposed. Subsequently, on the basis of the above on-chain data scalability scheme based on transactions, an on-chain data index based on skip lists is proposed to improve the retrieval efficiency. The experimental results show that both the on-chain data scalability schemes achieve on-chain data scalability while reducing storage overhead. Meanwhile, the on-chain data index based on skip lists has significantly improved dynamic range retrieval efficiency and reduced the time complexity of single data retrieval to O(log(n)).
3 August 2018 in Journal of Circuits, Systems and Computers
A low-power dual-mode receiver is presented for ultra-high-frequency (UHF) radio frequency identification (RFID) systems. The reconfigurable architecture of the tag is proposed to be compatible with low-power and high-sensitivity operating modes. The read range of RFID system and the lifetime of the tag are increased by photovoltaic, thermoelectric and RF energy-harvesting topology. The receiver is implemented in a 0.18-μm standard CMOS process and occupies an active area of 0.65 mm × 0.7 mm. For low-power mode, the tag is powered by the rectifier and the sensitivity is −18 dBm. For high-sensitivity mode, the maximum PCE of the fully on-chip energy harvester is 46.5% with over 1-μW output power and the sensitivity is −40 dBm with 880 nW power consumption under the supply voltage of 0.8 V.
This paper introduces a novel and efficient physical unclonable function (PUF) extraction method for SRAM. The proposed one-layer convolution scheme is based on a convolution operation, which significantly enhances the reliability of the PUF. To further reduce the hardware resources, a lightweight solution is presented based on a one-layer convolution scheme at the cost of a higher redundancy coefficient and a larger range for the inter-chip Hamming distance (HD). Both the above schemes only use certain hardware resources in the initial stage and the hardware resources are automatically released after PUF verification. The two schemes were verified using SRAM cells in three stm32f407 chips to output a 256-bit PUF response. The experimental results show that the one-layer convolution scheme required 8 KB SRAM, while the lightweight scheme used only 0.5 KB SRAM. The reliability of the one-layer convolution was found to be 100% when the redundancy coefficient was 0.08 and the inter-chip HD was 50.8073%. The reliability of the lightweight scheme was 100% and of the inter-chip HD was 50.195%.
This paper presents a novel adaptive reconfigurable rectifier architecture for radio frequency energy harvesting (RFEH); in addition, a new metric for high-efficiency dynamic range (DR) is proposed. The presented rectifier architecture is based on a double-sided diode-feedback cross-coupled differential-drive rectifier (CCDR) structure incorporating self-body bias for reconfigurable operation. An adaptive structure based on a Schmitt trigger is proposed to adaptively switch the rectifier connection without auxiliary voltage (Vaux), with two rectifier stages in parallel at low power and in series at high power. The system is simulated at a 180 nm CMOS process and the results show more than 17 dB DR at 900 MHz, with efficiency higher than 50% at a 100 kΩ load.