The global demand for sustainable energy is increasing due to urbanization, industrialization, population, and developmental growth. Transforming the large quantities of biomass resources such as agro-residues/wastes could raise the energy supply and promote energy mix. Residues of biomass instituted in the rural and industrial centers are enormous, and poor management of these residues results in several indescribable environmental threats. The energy potential of these residues can provide job opportunities and income for nations. The generation and utilization of dissimilar biomass as feedstock for energy production via densification could advance the diversity of energy crops. An increase in renewable and clean energy demand will likely increase the request for biomass residues for renewable energy generation via densification. This will reduce the environmental challenges associated with burning and dumping of these residues in an open field. Densification is the process of compacting particles together through the application of pressure to form solid fuels. Marketable densification is usually carried out using conventional pressure-driven processes such as extrusion, screw press, piston type, hydraulic piston press, roller press, and pallet press (ring and flat die). Based on compaction, densification methods can be categorized into high-pressure, medium-pressure, and low-pressure compactions. The common densification processes are briquetting, pelletizing, bailing, and cubing. They manufacture solid fuel with desirable fuel characteristics—physical, mechanical, chemical, thermal, and combustion characteristics. Fuel briquettes and pellets have numerous advantages and applications both in domestic and industrial settings. However, for biomass to be rationally and efficiently utilized as solid fuel, it must be characterized to determine its fuel properties. Herein, an overview of the densification of biomass residues as a source of sustainable energy is presented.
Integrating innovation and environmental responsibility has become important in pursuing sustainable industrial practices in the contemporary world. These twin imperatives have stimulated research into developing methods that optimize industrial processes, enhancing efficiency and effectiveness while mitigating undesirable ecological impacts. This objective is exemplified by the emergence of biochar derived from the thermo-chemical transformation of biomass. This review examines biochar production methods and their potential applications across various aspects of the iron and steel industries (ISI). The technical, economic, and sustainable implications of integrating biochar into the ISI were explored. Slow pyrolysis and hydrothermal carbonization are the most efficient methods for higher biochar yield (25–90%). Biochar has several advantages- higher heating value (30–32 MJ/kg), more porosity (58.22%), and significantly larger surface area (113 m2/g) compared to coal and coke. However, the presence of biochar often reduces fluidity in a coal-biochar mixture. The findings highlighted that biochar production and implementation in ISI often come with higher costs, primarily due to the higher expense of substitute fuels compared to traditional fossil fuels. The economic viability and societal desirability of biochar are highly uncertain and vary significantly based on factors such as location, feedstock type, production scale, and biochar pricing, among others. Furthermore, biomass and biochar supply chain is another important factor which determines its large scale implementation. Despite these challenges, there are opportunities to reduce emissions from BF-BOF operations by utilizing biochar technologies. Overall, the present study explored integrating diverse biochar production methods into the ISI aiming to contribute to the ongoing research on sustainable manufacturing practices, underscoring their significance in shaping a more environmentally conscious future.
17 January 2022 in International Journal of Renewable Energy Development
The United States Environmental Protection Agency (EPA) has reported that consumption of fossil fuels and their products has contributed about 65% of the global greenhouse gas emission. Therefore, it is expedient to look for alternative energy sources for an eco-friendly environment. The EPA recommended using biomass energy as a promising stabilization option to alleviate global climate change. This study focused on developing composites fuel briquettes from a blend of carbonized corncob and banana stalk. Carbonization was carried out at 380 oC, while 60 min was adopted as the residence time. Briquettes were manufactured at different blending ratios (90CC:10BS, 80CC:20BS, 70CC:30BS, 60CC:40BS and 50CC:50BS of corncob: banana stalk, respectively) and compaction pressures (50, 70 and 90 kPa) using gelatinized starch as binder. The manufactured briquettes' calculated and actual calorific values varied between 18.98-22.07 MJ/kg and 20.22-23.12 MJ/kg, respectively, while shatter indices were in the range of 38.22-89.34%. The compressed and relaxed densities of the fuel briquettes were in the range of 0.32-1.39 g/cm3 and 0.22-1.02 g/cm3, respectively. The relaxation ratio and water resistance properties varied between 1.11- 2.21 and 11-23 min, respectively. Analyses of the results revealed that compaction pressure, blending ratio, and particle size substantially affect the combustion and physico-mechanical characteristics of the manufactured fuel briquettes. When optimum combustion and physico-mechanical properties are required, a sample made from 90CC:10BS (S1) is recommended for use. The fuel briquettes manufactured in this study possess the required thermal and physico-mechanical properties of solid fuel; therefore, it is recommended for different applications.
1 December 2019 in Journal of Physics: Conference Series
Densification of agricultural residues such as husks, shells and cobs into fuel briquettes is an alternative renewable feedstock for producing solid fuels because it improves their physico-mechanical, storage and combustion properties. This paper presents the physico-mechanical characterisation of fuel briquettes made from blends of corncob and rice husk. The raw samples of corncob and rice husk were collected, sorted and pulverised. The pulverised samples were screened to 0.25, 1.0 and 1.75 mm particle sizes, blended at mixing ratios of 80:20, 70:30, 60:40, and 50:50, and afterwards, briquette samples were produced at 25, 50, and 65 kPa compaction pressures respectively with starch as the binder. The variations in the particle size, mixing ratio and compaction pressure have significantly influenced the investigated physico-mechanical properties of the produced briquettes. The briquette made from 80:20 mixing ratio of corncob to rice husk, 0.25 mm particle size and 65 kPa compaction pressure had the highest compressive strength of 111 kN/m2 and the least compressive strength of 39 kN/m2 from briquette with 50:50 ratio of corncob to rice husk, 1.75 mm particle size and 25 kPa compaction pressure. The briquette made from 50:50 mixing ratio of corncob to rice husk, 0.25 mm particle size and 65 kPa compaction pressure spent the longest time to collapse when immersed in water; taking up to 972 seconds and the least time of 480 seconds from briquette with 80:20 mixing ratio corncob to rice husk, 1.75 mm particle size and 25 kPa compaction pressure.
Recycled plastic wastes polyethylene terephthalate (PET), high-density polyethylene (HDPE) and polypropylene (PP) were studied in the presence of Ethylene glycidyl methacrylate (EGMA) copolymer compatibilizer, as raw materials for producing automobile bumper. These plastic wastes were cleaned and dried, then crushed to < 3 mm in size and further dried for 4 h to remove moisture. Crushed samples were weighed in different proportions with varying amount of compatibilizer (5–15 g) and manually mixed. Recycled composite plastic of 150 × 150 × 3 mm in length, width and thickness, respectively, was produced from weighed samples in an injection moulding machine at 150–220oC and pressure of 150 bar. Mechanical tests and morphological observation were carried out on the blend. The mechanical properties were more dependent on EGMA in the blend produced than the variation of the PET, PE and PP. The results showed that the optimum tensile strength (25.48 N/mm2), elongation at break (40.75%), Young’s modulus (1615.96 N/mm2) and impact strength (179 J/m) were obtained when 10 g of EGMA was used with 164: 18:18 g of PET, PEL and PP, respectively. The morphology of the sample examined showed the presence of discrete particles with cracks, cavities and various separations, and they defined the mechanical behaviour of the samples. Compared to some standard materials used to produce car bumper, the recycled blend in this study showed huge potential for its production and thus, the use can help in reducing environmental pollution caused by plastic waste.
The overdependence on fossils as the primary energy source has led to climate change, global warming, and the emission of greenhouse gas. As a result, the United Nations, while setting the goals for the year 2030, has made the provision of a green environment and energy one of the top priorities. In this study, the suitability of corncob for green energy production was investigated. The improvement of corncob’s thermal and combustion properties via the torrefaction process was considered for solid fuel applications. The raw corncob was collected, sorted, and dried for seven days before being used for the torrefaction experiment. Different torrefaction temperatures (200, 240, and 260 °C) and residence times (20, 40, 60 min) were studied. There was no particle reduction—samples were torrefied as collected (whole corncob). The results show that torrefaction temperature and residence time affect the torrefaction products yields along with their properties. Thermal and combustion properties were improved with an increase in torrefaction temperature and residence time. The higher heating value and energy density of the torrefied corncob varied between 17.26 and 18.89 MJ/kg, and 3.23 and 5.66 GJ/m3, respectively. High torrefaction temperature and residence time lead to low solid yield; however, liquid and gas yields increase with torrefaction temperature and residence time. The solid yields varied from 27.57 to 52.23%, while the liquid and gas yields varied from 31.56 to 44.78% and 16.21 to 27.65%, respectively. The properties of corncob improve after torrefaction and are suitable for solid fuel application.