The tail-sitter VTOL UAV boasts not only high-speed cruising and air hovering capabilities, but also its unique tail-sitting vertical takeoff and landing and hovering attitude enable aerial operations with an exceptionally small cross-sectional area. This feature effectively broadens the scope of application for the UAV in intelligent agriculture, encompassing tasks such as agricultural inspection, production monitoring, and topographic mapping. Given the necessity for frequent modal transitions, this paper is grounded in a thorough examination of the typical structural characteristics of the tail-sitter VTOL UAV. A comprehensive technical solution for tail-sitter VTOL UAVs, based on the free-tail configuration, is proposed in this paper. The free-tail structure is utilized to address the limitations of traditional tailless layout and fixed landing gear in terms of flight stability and takeoff/landing performance of tail-sitter VTOL UAVs. However, the implementation of this solution necessitates the addition of a new maneuvering unit. Consequently, this paper delves into the aerodynamic coupling characteristics and laws between the layout parameters such as tail number, tail length, and tail area and the tail-sitter VTOL UAV fuselage. To optimize the free-tail configuration, a multi-objective optimization is performed by integrating the overall UAV dynamics, landing dynamics, and modal transition trajectory constraints. The results of stability modeling simulations and flight tests demonstrate that the tail-sitter VTOL UAV equipped with this technical solution exhibits enhanced maneuverability and flight efficiency compared to the conventional tailless layout.
30 October 2024 in International Journal of Solids and Structures
The test of arresting hook bounce is one of the most essential technologies in the design and research of arresting hook. In order to research the dynamic performance of the hook after touchdown and impacting with the deck when the aircraft is arrested, an approach for a certain type of aircraft arresting hook bounce test is proposed in this paper. Solutions to critical technique issues arising in the test process such as aircraft sinking velocity control, aircraft horizontal velocity simulation, and simulation of the performance of the damper are derived and verified by the bounce test of the arresting hook. The bounce height, bounce distance, stroke length of the arresting hook damper after the hook is impacted are measured by the test. The test method proposed can be used for researching the bounce of arresting hook and providing reliable test data for the design of carrier-based aircraft and arresting hook.
The UAV cluster combat puts forward higher requirements for short-distance arresting gears for multitype aircraft. Based on magnetorheological technology, an arresting gear was designed, and the structural parameters of the MR damper were optimized. An iterative optimization method of structural parameters via a genetic algorithm combined with parametric modeling and magnetic field simulation was proposed. The optimization method was applied to optimize the structure of both a single-coil and double-coil damper. The performance of the optimized arresting gear was studied. The results show that, under the same zero field damping upper limit, the variation range of the damping force of the double coil increases by 10.2% compared with that of the single coil. Comparing the peak overload of UAV before and after the optimization, when the UAV mass increases from 4000 kg to 10,000 kg, the reduction in the peak acceleration is increased from 19.8% to 25.4%. Compared with traditional hydraulic arresting gear, the new arresting gear has good adaptability to UAVs with various qualities and has higher arresting efficiency. This arresting gear has a certain advanced nature.
Arresting gear systems play a vital role in carrier-based aircraft landing. In order to accurately understand the process of arresting hook and cable, this study introduces a parameter inversion method to model the arresting cable and applies it to the transient dynamics model of the arresting hook and cable. The feasibility of the arresting cable model and its application to the transient dynamics model of the arresting hook and cable are validated through arresting hook and cable impact tests. The study compares three different models of arresting cables for simulation results and concludes that assuming the arresting cable to be a beam with metal elastic parameters during the modeling process cannot ignore the influence of the cable’s torsional and bending stiffness on the modeling. The study also investigates the dynamic response of the arresting hook during the aircraft arrestment and hooking process and concludes that the stress peak of the hook arm is much lower throughout the entire arrestment process than at the moment of hooking the cable. The study further identifies factors that affect the stress on the arresting hook arm, such as the aircraft’s yaw angle, deck angle, cruising speed, and the initial position of the arresting hook and cable before engagement. The research results have significant implications for improving the design optimization of the structural strength of the functional components of the naval aircraft arresting system and provide theoretical guidance and technical reserves for subsequent related studies.
In order to research the safety characteristics of carrier-based aircraft in yaw arrest, a complete dynamic model of the arresting system of a certain type of aircraft was developed to understand more about its dynamic properties. Based on the discrete kink-wave model, a simulation of centering arrest was conducted. The simulation results were compared with experimental data from the United States (US) military standards, demonstrating that the basic changing laws are almost the same. On the basis of centering arrest, a simulation of yaw arrest was carried out. The results show that in yaw state, the difference in the lengths of the arresting cables on either side of the hook is smaller in the early stage after the hook hangs on the rope, which leads to little influence on load fluctuation produced by the kink-wave. With the increase in arresting distance, the difference in the lengths of the arresting cables on either side becomes larger, resulting in a situation in which the cable tension on the departure side will gradually become greater than that on the opposite side. In this situation, yaw landing has a negative impact on the characteristics of arresting safety, and the excessive yaw angle causes the aircraft to rush out of the safe landing area.