Here, we introduce phase change mechanisms in lead-free piezoceramics as a strategy to utilize attendant volume change for harvesting large electrostrain. In the newly developed (K,Na)NbO3 solid-solution at the polymorphic phase boundary we combine atomic mapping of the local polar vector with in situ synchrotron X-ray diffraction and density functional theory to uncover the phase change and interpret its underlying nature. We demonstrate that an electric field-induced phase transition between orthorhombic and tetragonal phases triggers a dramatic volume change and contributes to a huge effective piezoelectric coefficient of 1250 pm V−1 along specific crystallographic directions. The existence of the phase transition is validated by a significant volume change evidenced by the simultaneous recording of macroscopic longitudinal and transverse strain. The principle of using phase transition to promote electrostrain provides broader design flexibility in the development of high-performance piezoelectric materials and opens the door for the discovery of high-performance future functional oxides.
5 January 2022 in ACS Applied Materials & Interfaces
Microstructural design is a widespread approach to tailor the properties of functional materials with the size effect being an effective constraint that modifies physical phenomena. In this work, we investigate the grain size effect on the properties and the electric field induced phase transformation behavior in barium titanate. A broad range of unimodal average grain size distribution between 0.4 and 15 μm was successfully sintered avoiding abnormal grain growth. Samples with a grain size close to the range of 1–2 μm, balancing microstructural strain, presence, and mobility of domain walls to allow the field induced crystal phase transformation, showed optimal electromechanical and dielectric properties. By means of in situ high energy x-ray diffraction and a high-resolution multianalyzer detector, we distinguish and quantify a tetragonal–orthorhombic phase transformation induced by an electric field, providing unambiguous proof of this induced phase transformation. These results contribute to the understanding of fundamental questions about the piezoelectric effect in barium titanate and consequently other similar systems.
The electric field response of the lead-free solid solution (1−x)Bi0.53Na0.47TiO3–xBaTiO3 (BNT–BT) in the higher BT composition range with x = 0.12 was investigated using in situ synchrotron X-ray powder diffraction. An introduced Bi-excess non-stoichiometry caused an extended morphotropic phase boundary, leading to an unexpected fully reversible relaxor to ferroelectric (R–FE) phase transformation behavior. By varying the field frequency in a broad range from 10−4 up to 102 Hz, BNT–12BT showed a frequency-dependent gradual suppression of the field induced ferroelectric phase transformation in favor of the relaxor state. A frequency triggered self-heating within the sample was found and the temperature increase exponentially correlated with the field frequency. The effects of a lowered phase transformation temperature TR–FE, caused by the non-stoichiometric composition, were observed in the experimental setup of the freestanding sample. This frequency-dependent investigation of an R–FE phase transformation is unlike previous macroscopic studies, in which heat dissipating metal contacts are used.
(KNN)-modified morphotropic phase boundary (MPB) compositions of the two -based lead-free piezoelectrics, namely, (NBT-6BT) and (NBT-20KBT) are model systems exhibiting large electric-field-driven strain. There is a general perception that (i) increasing KNN concentration monotonically weakens the direct piezoelectric response , and (ii) maximum electrostrain occurs when KNN pushes the system in the fully ergodic relaxor state. We have examined these issues using various complementary techniques involving electrostrain, piezoelectric coefficient , ferroelectric switching-current measurements, and field-driven structural studies on the global and local scales using laboratory and synchrotron x-ray diffraction, neutron powder diffraction, and photoluminescence techniques. Our investigations revealed the following important features: (i) In the low-concentration regime, KNN induces a tetragonal ferroelectric distortion, which improves the weak signal piezoresponse. (ii) Beyond a threshold concentration, in-phase octahedral tilt sets in and weakens the long-range ferroelectric order to partially stabilize an ergodic state. (iii) The maximum electrostrain (∼0.6%) is achieved in the mixed (nonergodic + ergodic) state. (iv) The mixed state invariably exhibits a less-known phenomenon of field-driven ferroelectric-to-relaxor transformation during bipolar field cycling. (v) The enhanced electrostrain in the mixed state is associated with the electric field increasing the correlation lengths of the short-ranged tetragonal and rhombohedral ferroelectric regions without overall transformation of one phase to the other. We summarize the findings of this work in a comprehensive electric field composition (E-x) phase diagram. The findings reported here are likely to be true for other NBT-based MPB systems.
In this study, compositions containing green glass bottles and desiccated and crushed yerba mate (Ilex paraguarinensis) of different mass fractions (10-30%) were prepared to obtain glass foams for thermal insulation purposes. These compositions were uniaxially pressed (at 40 MPa), and the compact powders were fired at 850°C and 900°C for 60 min in order to investigate the effect of yerba mate and temperature on the formation of pores and the thermal and mechanical properties of the processed glass foams. The results indicated that the glass foams displayed porosities ranging from 65.3-88.3%, compressive strengths ranging from 15-1.5 MPa, and thermal conductivities ranging from 0.6-0.04 W·m-1·K-1. Cumulatively, these glass foams are candidate thermal insulators that have advantageous properties for various industrial applications.