The electric field–temperature (E–T) phase diagrams for three model compositions in the lead-free (Bi1/2Na1/2)TiO3–BaTiO3–(K1/2Na1/2)NbO3 (BNT–BT–KNN) relaxor system have been constructed, to serve as a template for other similar systems. The compositions chosen are known to exhibit nonergodic (BNT–6BT), ergodic (BNT–6BT–3KNN) and ferroelectric (BNT–12BT) behaviors at room temperature. Through temperature-dependent permittivity and piezoelectric measurements, the transition pathways across relaxor–ferroelectric states were determined as functions of temperature and electric field. The relaxor compositions were found to have a typical U-shaped E–T phase diagram and exhibited typical transitions to the ferroelectric phase upon applying electric fields above threshold values. BNT–6BT is suggested to have a freezing temperature (Tf) of approximately 120 °C and exhibited a “mixed” transition behavior between 90 °C and 120 °C, characterized by the presence of both partially pinched polarization hysteresis loops, characteristic of ergodic relaxors, and substantial negative strains, indicating a nonergodic behavior. Similar behavior was observed for BNT–6BT–3KNN, which had a rather broad temperature range (21 °C to −40 °C) where it exhibited the “mixed” transition behavior. The field required for the relaxor to ferroelectric transition was 20 kV cm−1 and 30 kV cm−1 for BNT–6BT and BNT–6BT–3KNN at Tf, respectively. BNT–12BT was ferroelectric at room temperature, however it transformed spontaneously to an ergodic relaxor at approximately 200 °C upon heating. Additionally, to study the influence of point defects on the E–T phase diagrams, nonstoichiometry was intentionally introduced to alter the oxygen vacancy concentration in the BNT–6BT composition. It was found that lowering the oxygen vacancy concentration lowers Tf, while increasing their concentration has the opposite effect. This provides an avenue to tune crucial materials’ parameters such as Tf and critical field values and modify their structural transition pathways to suit application requirements.
4 February 2020 in Journal of Materials Chemistry C
NBT-BT-based lead-free relaxors have attracted significant attention due to their excellent ferroelectric properties. They undergo a phase transformation to a ferroelectric state with domains, which plays an important role in their exhibited fatigue behavior. In case of non-ergodic relaxors (e.g. NBT-6BT) and ferroelectric compositions (e.g. NBT-12BT) domain wall pinning by oxygen vacancies leads to severe fatigue, while in case of ergodic relaxors (e.g. NBT-6BT-3(K1/2Na1/2)NbO3) domain wall pinning is relatively less effective. The importance of domain switching and concentration of oxygen vacancies has been further emphasized by comparing fatigue under unipolar and bipolar conditions, performing fatigue on NBT-6BT-3(K1/2Na1/2)NbO3 under non-ergodic (5 °C) and ergodic conditions (40 °C), and intentionally altering point defects concentration in NBT-6BT through non-stoichiometry. Furthermore, it has been shown that permanent fatigue due to electrode delamination and a blocking surface layer may commence at high numbers of fatigue cycles, depending upon the amplitude of fatigue waveform. Finally, the results obtained in this study have been summarized using a schematic.
The electric field response of the lead-free solid solution (1−x)Bi0.53Na0.47TiO3–xBaTiO3 (BNT–BT) in the higher BT composition range with x = 0.12 was investigated using in situ synchrotron X-ray powder diffraction. An introduced Bi-excess non-stoichiometry caused an extended morphotropic phase boundary, leading to an unexpected fully reversible relaxor to ferroelectric (R–FE) phase transformation behavior. By varying the field frequency in a broad range from 10−4 up to 102 Hz, BNT–12BT showed a frequency-dependent gradual suppression of the field induced ferroelectric phase transformation in favor of the relaxor state. A frequency triggered self-heating within the sample was found and the temperature increase exponentially correlated with the field frequency. The effects of a lowered phase transformation temperature TR–FE, caused by the non-stoichiometric composition, were observed in the experimental setup of the freestanding sample. This frequency-dependent investigation of an R–FE phase transformation is unlike previous macroscopic studies, in which heat dissipating metal contacts are used.
Relaxor ferroelectrics are technologically important materials for applications in, for example, high-temperature capacitors, transducers and nano-positioning systems. These materials have often been reported to exhibit surface or skin layers with distinct physical properties to the bulk. The control of formation and functionality of these skin layers has remained elusive and is becoming increasingly critical due to device miniaturization, where the surface contribution to overall material properties becomes significant. We recently demonstrated that the distinct structural distortion of the skin layer is intimately related to the internal chemical pressure applied by oxygen vacancies and the plane stress conditions at the surface. (S. Kong, N. Kumar, S. Checchia, C. Cazorla and J. Daniels, Adv. Funct. Mater., 2019, 29, 1900344) Here, we demonstrate a unique capability to control the formation and properties of the skin layer through the control of defect concentration. Most interestingly, the skin layer is polar and both electrically and optically active, making it functional and a new candidate for low operating voltage and/or optoelectronic devices. The surface domains in the skin could be altered by applying a small voltage bias (1000 times lower than bulk) or light illumination. A reversible optical change in surface domains provides a new non-contact external control to tune the material polarisation.
The temperature-dependent energy storage properties of four tungsten bronze-type ceramics are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. With different cations at A and B sites, those four ceramics exhibit different crystal structures and show significantly different microstructure features and dielectric responses with changing temperatures. It was observed under SEM that BZN has smaller grains and a more porous structure than BTN. SZN shows the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, they exhibit good temperature stability together with low dielectric loss. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.