Jonathan D.  Yuen

Dr. Jonathan D. Yuen

Center for Bio-Molecular Science and Engineering, U.S. Naval Research Laboratory, Washington, DC 20375, USA
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 April 2020 in Sensors
Verified
Journal Article
Open access
PDF file
JYJonathan D. Yuen
Jonathan D. Yuen
LSLisa Shriver-Lake
Lisa Shriver-Lake
Scott A. WalperScott A. Walper
Scott A. Walper
DZDaniel Zabetakis
Daniel Zabetakis
JBJoyce C. Breger
Joyce C. Breger
DSDavid A. Stenger
David A. Stenger
We demonstrate the viability of using ultra-thin sheets of microbially grown nanocellulose to build functional medical sensors. Microbially grown nanocellulose is an interesting alternative to plastics, as it is hydrophilic, biocompatible, porous, and hydrogen bonding, thereby allowing the potential development of new application routes. Exploiting the distinguishing properties of this material enables us to develop solution-based processes to create nanocellulose printed circuit boards, allowing a variety of electronics to be mounted onto our nanocellulose. As proofs of concept, we have demonstrated applications in medical sensing such as heart rate monitoring and temperature sensing—potential applications fitting the wide-ranging paradigm of a future where the Internet of Things is dominant.

6 May 2019 in Scientific Reports
Verified
Journal Article
Open access
PDF file
JYJonathan D. Yuen
Jonathan D. Yuen
ABAnkit Baingane
Ankit Baingane
QHQumrul Hasan
Qumrul Hasan
LSLisa Shriver-Lake
Lisa Shriver-Lake
SWScott A. Walper
Scott A. Walper
Gymama SlaughterGymama Slaughter
Gymama Slaughter
We present the first demonstration of a fully-flexible, self-powered glucose indicator system that synergizes two flexible electronic technologies: a flexible self-powering unit in the form of a biofuel cell, with a flexible electronic device - a circuit-board decal fabricated with biocompatible microbial nanocellulose. Our proof-of-concept device, comprising an enzymatic glucose fuel cell, glucose sensor and a LED indicator, does not require additional electronic equipment for detection or verification; and the entire structure collapses into a microns-thin, self-adhering, single-centimeter-square decal, weighing less than 40 mg. The flexible glucose indicator system continuously operates a light emitting diode (LED) through a capacitive charge/discharge cycle, which is directly correlated to the glucose concentration. Our indicator was shown to operate at high sensitivity within a linear glucose concentration range of 1 mM–45 mM glucose continuously, achieving a 1.8 VDC output from a flexible indicator system that deliver sufficient power to drive an LED circuit. Importantly, the results presented provide a basis upon which further development of indicator systems with biocompatible diffusing polymers to act as buffering diffusion barriers, thereby allowing them to be potentially useful for low-cost, direct-line-of-sight applications in medicine, husbandry, agriculture, and the food and beverage industries.

13 November 2006 in Applied Physics Letters
Verified
Journal Article
Closed access
JGJieun Ghim
Jieun Ghim
KBKang-Jun Baeg
Kang-Jun Baeg
YNYong-Young Noh
Yong-Young Noh
SKSeok-Ju Kang
Seok-Ju Kang
JJJang Jo
Jang Jo
AHAlan J. Heeger
Alan J. Heeger
A thermally cross-linkable perfluorocyclobutane (PFCB) polymer was synthesized and examined for use as the gate dielectric in organic thin film transistors (OTFTs). The PFCB polymer showed good solvent and process resistance during the photolithographic patterning of the electrodes. Bottom contact OTFTs were fabricated with poly(3-hexylthiophene)-2,5-diyl (P3HT) as the semiconductor, either spin cast or dip coated, on the PFCB gate dielectric. OTFTs fabricated with dip-coated P3HT showed a field effect mobility of 1.8×10−3cm2∕Vs and a high on/off current ratio of 8.3×106 in the saturation regime, with a source-drain voltage of VD=−50V.