To improve the sensitivity of the magnetic tunnel junction(MTJ)sensor, a novel architecture for a double-gap magnetic flux concentrator (MFC) was studied theoretically and experimentally in this paper. The three-dimensional finite element model of magnetic flux was established to optimize the magnetic field amplification factor, with different gaps. The simulation results indicate that the sensitivity of an MTJ sensor with a double-gap MFC can be significantly better than that of a sensor with a traditional single-gap MFC, due to the fact that the magnetic magnification sharply increases with the decrease in effective gap width. Besides this, the half-bridge MTJ sensors with the double-gap MFC were fabricated using photolithography, ion milling, evaporation, and electroplating processes. Experimental results show that the sensitivity of the MTJ sensor increased by ten times compared to the sensor without the double-gap MFC, which underlines the theoretical predictions. Furthermore, there is no significant increase in the sensor noise. The work in this paper contributes to the development of high-performance MTJ sensors.

A highly sensitive superconductor/tunnel magnetoresistance (TMR) composite magnetic sensor was designed and fabricated to satisfy the demands of detecting weak magnetic fields down to the pT range at low frequencies. First, analysis of the 1/f noise provided an optimized design scheme for the TMR unit to reduce the noise level. Then, the key structural parameters of the superconducting flux transformation amplifier (SFTA) were optimized with focus on the bonding quality between SFTA and TMR units using the finite element method to enhance the magnetic field magnification factor. An SFTA–TMR composite method with secondary alignment and multi-step bonding was proposed to fabricate the composite magnetic sensor and ensure the designed bonding gap and alignment accuracy. Experiments showed that the magnetic field sensitivity reached 5 pT/Hz^0.5 (@ 13 Hz), which is beyond the highest level of superconductor/TMR composite magnetic sensors reported to date and is a further step toward the application of weak magnetic field detection.

The low frequency magnetic field detection ability of magnetoresistive (MR)sensor is seriously affected by 1/f noise. At present, the method to suppress the influence of low frequency noise is mainly to modulate the measured magnetic field by mechanical resonance. In this paper, a novel modulation concept employing a magnetoelectric coupling effect is proposed. A design method of modulation structure based on an equivalent magnetic circuit model (EMCM) and a single domain model of in-plane moment was established. An EMCM was established to examine the relationship between the permeability of flux modulation film (FMF) and modulation efficiency, which was further verified through a finite element simulation model (FESM). Then, the permeability modulated by the voltage of a ferroelectric/ferromagnetic (FE/FM) multiferroic heterostructure was theoretically studied. Combining these studies, the modulation structure and the material were further optimized, and a FeSiBPC/PMN-PT sample was prepared. Experimental results show that the actual magnetic susceptibility modulation ability of FeSiBPC/PMN-PT reached 150 times, and is in good agreement with the theoretical prediction. A theoretical modulation efficiency higher than 73% driven by a voltage of 10 V in FeSiBPC/PMN-PT can be obtained. These studies show a new concept for magnetoelectric coupling application, and establish a new method for magnetic field modulation with a multiferroic heterostructure.

The strong spin filtering effect can be produced by C-Ni atomic orbital hybridization in lattice-matched graphene/Ni (111) heterostructures, which provides an ideal platform to improve the tunnel magnetoresistance (TMR) of magnetic tunnel junctions (MTJs). However, large-area, high-quality graphene/ferromagnetic epitaxial interfaces are mainly limited by the single-crystal size of the Ni (111) substrate and well-oriented graphene domains. In this work, based on the preparation of a 2-inch single-crystal Ni (111) film on an Al₂O₃ (0001) wafer, we successfully achieve the production of a full-coverage, high-quality graphene monolayer on a Ni (111) substrate with an atomically sharp interface via ambient pressure chemical vapor deposition (APCVD). The high crystallinity and strong coupling of the well-oriented epitaxial graphene/Ni (111) interface are systematically investigated and carefully demonstrated. Through the analysis of the growth model, it is shown that the oriented growth induced by the Ni (111) crystal, the optimized graphene nucleation and the subsurface carbon density jointly contribute to the resulting high-quality graphene/Ni (111) heterostructure. Our work provides a convenient approach for the controllable fabrication of a large-area homogeneous graphene/ferromagnetic interface, which would benefit interface engineering of graphene-based MTJs and future chip-level 2D spintronic applications.

The orthogonal two-step annealing process is an effective strategy to linearize the response of magnetic tunnel junctions for magnetic field sensors. However, the response after the orthogonal annealing is inevitably modulated by the Neel effect from the reference layer, which results in an unexpected shift of the linear interval and a disappointing sensitivity deterioration in the weak field. Here, a non-orthogonal two-step annealing method is proposed to suppress the shift by compensating for the Neel coupling field. Experimental results show that the curve shift of junctions annealed in the non-orthogonal direction of 120° is 47.6% lower than that in the orthogonal one, with a significant sensitivity promotion in the weak field and little hysteresis increment. A simple energy minimization model is introduced to explain the results. Based on the model, the suppression of the curve shift is fulfilled with the effective field compensation for the Neel coupling field, modulated by the non-orthogonal annealing. Finally, Wheatstone bridge devices are constructed, and the bridge with non-orthogonally annealed junctions is found to have an increased sensitivity of 46.8% in the major loop along the sensing axis. Additionally, the non-orthogonal annealing method is also effective in suppressing the cross sensitivity, which is important for further application to three-axis magnetic sensors.