Seok-Hyun Lee

Seok-Hyun Lee


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2018 in IEEE Access
Verified
Journal Article
Open access
HJhai young Jung
hai young Jung
SKSung Hwan Kim
Sung Hwan Kim
BMByunghee Moon
Byunghee Moon
SLSeok-Hyun Lee
Seok-Hyun Lee
A conventional two-switch buck-boost (TSBB) converter can operate in buck, boost, and buck-boost modes. This paper introduces a new topology for a two-switch buck-boost converter with the same operation modes. However, the proposed TSBB converter has fewer conductions and switching components than the conventional TSBB converter, which reduces the power losses.

21 August 2022 in Sensors
Verified
Journal Article
Open access
PDF file
SLSeok-Hyun Lee
Seok-Hyun Lee
Jaehwan KimJaehwan Kim
Jaehwan Kim
Cellulose, the most abundant sustainable material on Earth, has excellent mechanical and physical properties, high optical transparency, biocompatibility, and piezoelectricity. So, it has many possibilities for future materials, and many researchers are interested in its application. In this paper, cellulose nanofiber (CNF) and CNF/polyvinyl alcohol (PVA) films are made, and their vibration energy harvesting is studied. CNF was isolated by chemical and physical methods, and the CNF suspension was cast on a flat substrate to make a film. A cast CNF wet film stayed in a 5 Tesla superconductor magnet for 7 days, which resulted in CNF alignment perpendicular to the magnetic field. To further improve the mechanical properties of the CNF film, mechanical stretching was applied. The CNF suspension was mixed with PVA, giving the film toughness. The cast CNF/PVA wet film was mechanically stretched and dried, which improved the CNF alignment. The fabricated CNF and CNF/PVA films were characterized using scanning electron microscopy and X-ray diffraction to verify the alignment. By stretching, the aligned CNF/PVA film exhibits the largest mechanical properties along the aligned direction. The maximum Young’s modulus and tensile strength of the 50% stretched CNF/PVA film are 14.9 GPa and 170.6 MPa, respectively. Finally, a vibration energy harvesting experiment was performed by invoking the piezoelectric behavior of the pure CNF, and 50% stretched CNF/PVA films. The harvester structure was innovated by adopting a cymbal structure, which was beneficial to producing large in-plane strain on the films. The designed cymbal structure was analyzed using ANSYS, and its natural frequency was experimentally verified. The CNF/PVA film performs better vibration energy harvesting than the pure CNF film. The CNF/PVA film is applicable for biocompatible and flexible vibration energy harvesting.

27 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SKSunghwan Kim
Sunghwan Kim
HJhai young Jung
hai young Jung
SLSeok-Hyun Lee
Seok-Hyun Lee
In this study, a modified design of a two-switch buck-boost (TSBB) converter is proposed to improve power efficiency using fewer conduction components, and the optimal power range is measured. The proposed TSBB converter operates in three topologies: buck, boost, and buck-boost, like the conventional TSBB converter. However, the proposed converter improves the power efficiency in the buck and buck-boost topologies by decreasing conduction loss using the diode in the switch-off section while maintaining the same number of semiconductors as that in the conventional TSBB converter. The power efficiency of the buck topology improves for the power range 10–80 W in the constant voltage (CV) and constant current (CC) modes; it increases on average by 0.75–1.36% and 0.83–2.27% in the CV and CC modes, respectively. The power efficiency of the buck-boost topology step-down improves for the 10–80 W in all modes. This increases the average by 0.73–0.99% and 3.33–4.75% in the CV and CC modes, respectively. The power efficiency of the buck-boost topology step-up increases on average by 1.65–2.00% for 10–80 W in the CV mode. In the CC mode, it increases by 2.17–2.77% on average for 10–50 W.

13 March 2019 in IEEE Access
Verified
Journal Article
Open access
SKSunghwan Kim
Sunghwan Kim
SLSeok-Hyun Lee
Seok-Hyun Lee
This paper proposes a new high-performance light-emitting diode (LED) converter with separation of the AC and DC driving parts for a T8 LED tube. The proposed LED converter is mounted at the end of the LED tube in G13 base and G13 base dummy. The separation of the AC and DC driving parts enhances the light uniformity of the LED tube by securing the optical distance between the optic cover and light source. The AC driving part was designed to be inserted in a G13 base and was connected with the DC driving part through an LED module. The proposed LED converter is based on single-stage buck-boost topology and was designed for the operation at 19 W for a 1200 mm T8 LED tube. The proposed LED converter is very small and has fewer parts than other LED converters but still has high performance. The measurement results of the proposed LED converter show that the line regulation of the LED output current is less than 3.4% at 100-240 VAC and achieves high circuit efficiency (>89%), high power factor (>0.93), and low total harmonic distortion (<;9%). In addition, all the current harmonics of the converter meet the requirements of the IEC 61000-3-2 Class C standards for high-performance LED lighting applications.

18 September 2022 in Electronics
Verified
Journal Article
Open access
PDF file
SLSeok-Hyun Lee
Seok-Hyun Lee
Jaehwan KimJaehwan Kim
Jaehwan Kim
Remotely driven smart actuator technology by microwave is attractive since it simplifies and reduces the complexity and weight of the remote system. A rectifying antenna (rectenna) array receives and converts microwave power into DC power for actuators, and the power collected from the rectenna array should be accurately allocated and distributed to each actuator. In this research, a new power distribution (PD) logic circuit is studied to control an actuator array effectively. The PD logic circuit was designed and tested to validate it. The preliminary design was tested for a 4 × 4 piezoelectric actuator array with a 16 dual-gate MOSFET array and a computer-controlled 16-channel DAC board. Additionally, power compensation as a remedial approach for a partial power failure of the array was integrated. This PD scheme with a new logic device simplifies the thousands of control cables required for connecting each array element. The performance and limitations of the designed PD circuit are discussed.

21 November 2008 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
SKSun Kim
Sun Kim
SLSeok-Hyun Lee
Seok-Hyun Lee
JSJeong-Hyun Seo
Jeong-Hyun Seo
HSHoyoung Song
Hoyoung Song
A new reset waveform for a large-sustain-gap structure in an ac plasma display panel is proposed. In the driving of a large-sustain-gap structure with a conventional ramp reset waveform, we cannot avoid the condition of an address electrode being a cathode, which causes lots of trouble in stabilizing the reset discharge. To resolve these problems, a square pulse instead of the conventional rising-ramp pulse is used. In order to stabilize the strong discharge in which the address electrode becomes a cathode, a priming discharge between the address (anode) and scan (cathode) electrodes is made prior to making a strong discharge between the address (cathode) and scan (anode) electrodes. With this scheme, a minimum address voltage of 60 V when the sustain gaps are 250 and 350 mum, respectively, is obtained. However, the contrast ratio using the square reset pulse is lower than that using the conventional ramp pulse. To improve the contrast ratio, the reset waveforms in each subfield are replaced by selective erase waveforms except for the first subfield. In the case of nonselective reset waveform, the background luminance is 19.4 cd/m2, whereas the background luminance of 2.4 cd/m2 is obtained with selective reset waveform.