Chunyan Li

Prof. Chunyan Li


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 April 2022 in Journal of Non-Crystalline Solids
Verified
Journal Article
Closed access
CLChunyan Li
Chunyan Li
JZJianshu Zhai
Jianshu Zhai
LTLin Tian
Lin Tian
YLYu Lu
Yu Lu
XLXiaocheng Li
Xiaocheng Li
SKShengzhong Kou
Shengzhong Kou

4 May 2020 in Surface Engineering
Verified
Journal Article
Closed access
CLChunyan Li
Chunyan Li
HWHaibo Wang
Haibo Wang
JDJuanqiang Ding
Juanqiang Ding
SWShunping Wang
Shunping Wang
JLJinling Li
Jinling Li
SKShengzhong Kou
Shengzhong Kou
In this study, Fe-based amorphous coatings were fabricated on 304 stainless steel by high-velocity oxyfuel (HVOF). Moreover, the properties of Fe-based amorphous coatings heat-treated at 150°C and 250°C were investigated. The XRD analysis shows that the structure of heat-treated amorphous coatings is all amorphous, and the porosity of heat-treated amorphous coatings is lower than that of original amorphous coatings. With the heat-treated temperature increasing, the corrosion resistance of amorphous coatings is improved in artificial seawater. Compared with the original coatings, the heat-treated amorphous coatings have great creep resistance. The wear resistance of heat-treated amorphous coatings is excellent than original amorphous coatings in artificial seawater and dry friction condition. The experiment results point out that the heat-treated amorphous coatings have excellent properties, which can improve properties of Fe-based amorphous coatings.

29 February 2012 in Progress in Natural Science: Materials International
Verified
Journal Article
Open access
CLChunyan Li
Chunyan Li
SKShengzhong Kou
Shengzhong Kou
YZYanChun Zhao
YanChun Zhao
GLGuangqiao Liu
Guangqiao Liu
YDYutian Ding
Yutian Ding
The effect of cooling rate on plastic deformation of Zr-based bulk metallic glasses has been studied. The specimens with the diameters of 3mm, 4mm and 6mm cut from the same ladder-shaped Zr55Al10Ni5Cu30 BMG rod were used in the present investigation. The experimental results indicated that the different plastic strains were induced for the three type compression specimens. The compressive plastic strain increased with the decreasing diameter for the as-cast specimens, which means that the compressive plastic strain increased with the increasing cooling rate. The reason of the difference is attributed to the free volume existed in the BMGs during the rapid solidification, and the larger free volume was contained in the specimen fabricated with the higher cooling rate. It has been found that the prominent serrations and multiple shear bands appeared during the compressive deformation tests of the specimen with smaller diameter of 3mm, indicating that the specimen with smaller diameter exhibits better plasticity due to more free volume content

1 October 2021 in Journal of Non-Crystalline Solids
Verified
Journal Article
Closed access
JLJinling Li
Jinling Li
CLChunyan Li
Chunyan Li
SWShunping Wang
Shunping Wang
HWHaibo Wang
Haibo Wang
SKShengzhong Kou
Shengzhong Kou

14 December 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
ZZZhenxiang Zhao
Zhenxiang Zhao
CLChunyan Li
Chunyan Li
YLYuchen Liu
Yuchen Liu
CLChunling Li
Chunling Li
SKShengzhong Kou
Shengzhong Kou

24 January 2019 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
CLChunyan Li
Chunyan Li
JYJinfeng Yin
Jinfeng Yin
JDJuanqiang Ding
Juanqiang Ding
FZFuping Zhu
Fuping Zhu
FXFei Xu
Fei Xu
SKShengzhong Kou
Shengzhong Kou