YanChun Zhao

Dr. YanChun Zhao

Lanzhou University of Technology, Lanzhou, Gansu, China
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 March 2024 in Physical Chemistry Chemical Physics
Verified
Journal Article
Closed access
PDF file
Faqi ZhanFaqi Zhan
Faqi Zhan
GWGuochang Wen
Guochang Wen
RLRuixin Li
Ruixin Li
CFChenchen Feng
Chenchen Feng
Yisi LiuYisi Liu
Yisi Liu
PLPei Qing La
Pei Qing La
A comprehensive review on oxygen vacancy modified photocatalysts including synthesis (controllability of location, content, etc. ), characterization (qualitative, quantitative and locational analysis), and applications and mechanisms.

24 April 2024 in Corrosion Science
Verified
Journal Article
Closed access
LFLi Feng
Li Feng
YYYang Yang
Yang Yang
YZYanChun Zhao
YanChun Zhao
KMKai Ma
Kai Ma
JCJunpeng Cui
Junpeng Cui

8 March 2025 in Rare Metals
Verified
Journal Article
Closed access
PDF file
YZYanChun Zhao
YanChun Zhao
HMHu‐Wen Ma
Hu‐Wen Ma
JSJian‐Dong Sun
Jian‐Dong Sun
JLJun‐Hui Luo
Jun‐Hui Luo
YSYu Su
Yu Su
PLPeter K. Liaw
Peter K. Liaw

14 January 2020 in Coatings
Verified
Journal Article
Open access
PDF file
GLGuang Li
Guang Li
YGYouyi Gan
Youyi Gan
CLChenheng Liu
Chenheng Liu
YSYu Shi
Yu Shi
YZYanChun Zhao
YanChun Zhao
SKShengzhong Kou
Shengzhong Kou
Fe-based amorphous coatings were prepared on the surface of 45 steel substrates via supersonic plasma spraying and laser cladding. The corrosion and wear behavior of the two different coatings were investigated. Compared with supersonic plasma spraying, laser cladding resulted in coatings with a relatively denser structure, lower porosity, less cracks, and a good metallurgical bond with the substrate. Thanks to these properties, coatings produced by laser cladding exhibit a higher ability to resist uniform corrosion and better friction and wear performance than plasma-sprayed coatings.

1 February 2010 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
YZYanChun Zhao
YanChun Zhao
SKShengzhong Kou
Shengzhong Kou
HSHongli Suo
Hongli Suo
RWRenjun Wang
Renjun Wang
YDYutian Ding
Yutian Ding

29 February 2012 in Progress in Natural Science: Materials International
Verified
Journal Article
Open access
CLChunyan Li
Chunyan Li
SKShengzhong Kou
Shengzhong Kou
YZYanChun Zhao
YanChun Zhao
GLGuangqiao Liu
Guangqiao Liu
YDYutian Ding
Yutian Ding
The effect of cooling rate on plastic deformation of Zr-based bulk metallic glasses has been studied. The specimens with the diameters of 3mm, 4mm and 6mm cut from the same ladder-shaped Zr55Al10Ni5Cu30 BMG rod were used in the present investigation. The experimental results indicated that the different plastic strains were induced for the three type compression specimens. The compressive plastic strain increased with the decreasing diameter for the as-cast specimens, which means that the compressive plastic strain increased with the increasing cooling rate. The reason of the difference is attributed to the free volume existed in the BMGs during the rapid solidification, and the larger free volume was contained in the specimen fabricated with the higher cooling rate. It has been found that the prominent serrations and multiple shear bands appeared during the compressive deformation tests of the specimen with smaller diameter of 3mm, indicating that the specimen with smaller diameter exhibits better plasticity due to more free volume content