In this study, calcination tests were performed on a mixed sample of lithium cobalt oxide and activated carbon at 300–1000 °C under an argon atmosphere. The tests were conducted to discover an effective method for recovering lithium and cobalt from the cathode active material used in lithium-ion batteries. Additionally, the effect of soluble fluorine on the purification of lithium carbonate was investigated by the addition of lithium fluoride to an aqueous lithium hydroxide solution and a CO2 flow test was performed. The lithium recovery was ≥90% when the calcination occurred at temperatures of 500–600 °C. However, the percent recovery decreased at temperatures ≥700 °C. It was demonstrated that in order to increase the recovery while maintaining 99% purity of lithium carbonate in the recovered material, it was imperative to increase the temperature of the solution and to limit the F/Li ratio (mass%/mass%) in the solution to a value that did not exceed 0.05.
The recovery of platinum group metals (PGMs) from waste materials involves dissolving the waste in an aqueous solution. However, since PGMs are precious metals, their dissolution requires strong oxidizing agents such as chlorine gas and aqua regia. In this study, we aimed to recover PGMs via the calcination of spent automotive catalysts (autocatalysts) with Li salts based on the concept of “spent autocatalyst + waste lithium-ion batteries” and leaching with only HCl. The results suggest that, when Li2CO3 was used, the Pt content was fully leached, while 94.9% and 97.5% of Rh and Pd, respectively, were leached using HCl addition. Even when LiF, which is a decomposition product of the electrolytic solution (LiPF6), was used as the Li salt model, the PGM leaching rate did not significantly change. In addition, we studied the immobilization of fluorine on cordierite (2MgO·2Al2O3·5SiO2), which is a matrix component of autocatalysts. Through the calcination of LiF in the presence of cordierite, we found that cordierite thermally decomposed, and fluorine was immobilized as MgF2.
In order to effectively recover Li from cathode active materials of lithium-ion batteries, model samples of LiCoO2 mixed with polyvinylidene fluoride (PVDF) were calcined at temperatures of 350–700 °C under an Ar or air atmosphere. Complete Li recovery was achieved by calcining the model sample at 400 °C under an Ar atmosphere, followed by water leaching. Additionally, to immobilize PVDF-derived F, an impurity in Li purification, we explored the use of calcium compounds (Ca(OH)2 and CaCO3) and a layered double hydroxide in both dry and wet processing methods. In the wet process, F was fixed by adding Ca(OH)2 to an aqueous LiF solution containing 1000 ppm of F. We confirmed that 98.6% of F was successfully removed from the solution after repeated fixation procedures. Furthermore, the unreacted Ca in the solution was separated and removed as CaCO3 by concentrating the solution.
7 September 2018 in Eurasian Chemico-Technological Journal
Self-supporting AC (activated carbon)-FWCNT (few-wall carbon nanotubes) hybrid electrodes were fabricated by mixing of ACs with high specific surface area (SSA) and sub-millimeter-long FWCNTs. In order to fabricate the hybrid electrodes, AC and FWCNT were mixed in a weight ratio of 9:1, dispersed by bath-sonication and vacuum-filtrated on a membrane filter. The addition of FWCNTs gives conductivity and mechanical strength, and replace metallic current collectors in thick (0.1 mm) electrodes. For making an electrode, three different ACs that derived from walnut shell (WS), that from apricot stones (AS), and that commercially used for capacitors (YP-80F, Kuraray Chemical Co., Osaka Japan), were used with FWCNT in weight ratio of AC:FWCNT = 9:1. An electrode based only on FWCNT was also prepared as a reference for comparison. Electrochemical properties of the obtained electrodes were investigated by the cyclic voltammetry method (CV). Electrochemical characteristics were measured using the three-electrode cell contained of YP-80F-FWCNT, AS-FWCNT, WS-FWCNT as a working electrode, a YP-80F-FWCNT counter electrode and a Ag/AgCl reference electrode with an electrolyte of 1 M Na2SO4 aqueous solution. Also, the morphological properties of obtained electrodes were studied using scanning electron microscope (SEM), the SSA was investigated by the Brunauer-Emmett-Teller analysis. SSA, conductivity, and resistivity of AS-FWCNT and WS-FWCNT electrodes were summarized. Both the AS-FWCNT and WS-FWCNT hybrid electrodes showed specific capacitances of about 140 F/g at 1 mV/s and about 100 F/g at 100 mV/s, which are similar or even better than the AC-CNT hybrid electrode made of commercialized AC (YP-80F).
In this study, we conducted trace element analysis using laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to quantitatively analyze the distribution of tramp elements and their coexistence states with other elements in recycled steel materials. The concentration distributions of Cu, Sn, Pb, Ag, and Au in a 455 µm × 270 µm region were measured using electric furnace steel as a sample by continuous line analysis. Although the concentration of Cu was the highest among the measured elements, the degree of variation in Cu concentration was the smallest. Meanwhile, not only were the degrees of variation of the Sn, Pb, and Ag concentrations large, but also the points of high concentration measurements tended to coincide. The coexistence states were investigated by determining the coefficient of correlation between the concentrations of two elements.
2 March 2017 in Journal of Material Cycles and Waste Management