This article presents an analysis of the performance of a 14.04 kWp grid-connected photovoltaic (PV) installation consisting of monocrystalline silicon, polycrystalline silicon and bifacial glass–glass monocrystalline silicon modules. The photovoltaic system was mounted in Poland, a location characterized by temperate climate conditions. On the basis of the obtained results, the photovoltaic parameters were determined in accordance with the international standard. The annual energy yield of the entire system was 1033 kWh/kWp, and the performance ratio achieved was 83%. The highest average daily final yield was in the range of 4.0–4.5 kWh/kWp for each photovoltaic technology under investigation. In the cold part of the year, the efficiency of the photovoltaic modules was estimated to be 15%, and it was estimated to be 7% during the warm part of the year. Array capture losses accounted for around 0.75 kWh/kWp of energy loss per day, whereas the inverter efficiency was over 95% during the months that are beneficial for energy production.
Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Its exceedance of the standard’s permissible amount carries the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The research presented in this paper is aimed at verifying whether it is possible to test the moisture content of diesel using impedance spectroscopy. To date, it is the first such attempt with commercially available diesel using this method, which, once refined, could be used in situ. The authors propose and apply a novel technique that is able to be used when the electrical properties of tested oils are unknown. The experimental results obtained show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.
This paper analyzes the influence of the skin effect and the proximity effect on the inductance and impedance of thin conductive layers. The motivation for taking up this topic is the initial assessment of the possibility of using conductive layers deposited with the PVD technique on textile materials as strip or planar transmission lines of high-frequency signals (e.g., for transmitting images). This work pursues two goals. The first of them is to develop and test a numerical procedure for calculating the electromagnetic field distribution in this type of issue, based on the fundamental solution method (FSM). The second aim is to examine the impact of the skin phenomenon on the resistance, inductance and impedance of thin conductive paths. The correctness and effectiveness of FSM for the analysis of harmonics of electromagnetic fields in systems containing thin conductive layers were confirmed. Based on the performed simulations, it was found that in the frequency range above 10 MHz, the dependence of resistance and impedance on frequency is a power function with an exponent independent of the path width. Moreover, it was found that for paths with a width at least several times greater than their thickness, the dependence of the phase shift between current and voltage on frequency practically does not depend on the path width.
Power electronic converters, next to PV panels, are an important element of PV systems. They are responsible for converting electrical energy parameters such as: voltage, current and frequency values. This paper presents a detail performance analyze and simulation studies of small photovoltaic energy system. The proposed system consist: a step-up converter fed from the PV array, a high-frequency transformer, a full wave rectifier and output inverter provides power to the grid. Converter is designed for load of 3.5 kW. The one step method (square wave) and sinusoidal pulse width modulation (SPWM) are used for switching the inverters circuit. The discussed system has been simulated in PSIM and the selected results are presented.
Realisation of a high-speed drive using a BLDC motor, especially that of low and medium power and with rotational speed of up to 40 000 rpm designed for use in aviation appliances, became possible due to rapid progress in electronic power control technology. An increase of both capability and diversity of electronic power circuits results from the increase of semiconductor element voltage and current operational ranges simultaneously with the improvement of their dynamical parameters, as well as from application of up-to-date microprocessor and programmable circuits for control purposes. Choice of topology for a drive system to be used in aviation appliances, including the electronic power converter, is based on the following quality and economy-related criteria: single-phase supply and sinusoidal waveform of power network current; high efficiency and reliability; small overall dimensions; minimum number of semiconductor elements; and low price. Various technical solutions are possible here, concerning both the scope of the power circuit and the control system.
The article concerns the issues related to the concept of power in a description of the non-linear receiver. The definitions of signals given in the applicable standards (norms) were used and the analysis of samples received from active experiments was carried out. A set of a drive system consisting of a thyristor converter and a DC motor was examined. The Elspec Blackbox G4500 energy quality analyzer was used for the measurements. The results were compiled in the form of many graphs in the time and frequency form. The analysis shows that during unloaded operation, undesirable power is mainly absorbed (passive and current distortions), while the active power is pulsating. It is noted that the nonlinearity of the receiver causes deterioration of the system's power.