Ali Al-Sayyab

Mr. Ali Al-Sayyab

PhD student
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in International Journal of Refrigeration
Verified
Journal Article
Open access
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
JNJoaquín Navarro-Esbrí
Joaquín Navarro-Esbrí
Adrián Mota-BabiloniAdrián Mota-Babiloni
Adrián Mota-Babiloni

1 September 2018 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
AMAkeel MA Morad
Akeel MA Morad
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
MAMohammed A. Abdulwahid
Mohammed A. Abdulwahid

1 January 2021 in Energy Conversion and Management
Verified
Journal Article
Closed access
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
Adrián Mota-BabiloniAdrián Mota-Babiloni
Adrián Mota-Babiloni
JNJoaquín Navarro-Esbrí
Joaquín Navarro-Esbrí

1 September 2019 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
ZTZainab Y. Al Tmari
Zainab Y. Al Tmari
MTMaher K. Taher
Maher K. Taher

13 June 2021 in Energies
Verified
Journal Article
Open access
PDF file
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
JNJoaquín Navarro-Esbrí
Joaquín Navarro-Esbrí
VFVíctor Manuel Soto Francés
Víctor Manuel Soto Francés
Adrián Mota-BabiloniAdrián Mota-Babiloni
Adrián Mota-Babiloni
This work focused on a compound PV/T waste heat driven ejector-heat pump system for simultaneous data centre cooling and waste heat recovery for district heating. The system uses PV/T waste heat as the generator’s heat source, acting with the vapour generated in an evaporative condenser as the ejector drive force. Conventional and advanced exergy and advanced exergoeconomic analyses are used to determine the cause and avoidable degree of the components’ exergy destruction rate and cost rates. Regarding the conventional exergy analysis for the whole system, the compressor represents the largest exergy destruction source of 26%. On the other hand, the generator shows the lowest sources (2%). The advanced exergy analysis indicates that 59.4% of the whole system thermodynamical inefficiencies can be avoided by further design optimisation. The compressor has the highest contribution to the destruction in the avoidable exergy destruction rate (21%), followed by the ejector (18%) and condenser (8%). Moreover, the advanced exergoeconomic results prove that 51% of the system costs are unavoidable. In system components cost comparison, the highest cost comes from the condenser, 30%. In the same context, the ejector has the lowest exergoeconomic factor, and it should be getting more attention to reduce the irreversibility by design improving. On the contrary, the evaporator has the highest exergoeconomic factor (94%).

1 May 2025 in Journal of Engineering and Sustainable Development
Verified
Journal Article
Open access
PDF file
FSFouad Alwan Saleh
Fouad Alwan Saleh
AMAbdulrahman Shakir Mahmood
Abdulrahman Shakir Mahmood
MAMohammed Kadhim Allawi
Mohammed Kadhim Allawi
Ali Al-SayyabAli Al-Sayyab
Ali Al-Sayyab
The natural gas can readily serve as the replacement fuel for internal combustion engines. This work tested the SI engine when running on a hydrogen-enriched compressed natural gas (CNG) mixture. The modelling has been implemented at a range of engine speeds from 1000 to 5500 rpm with a full load, direct injection, and a spark-ignited engine with a compression ratio of 10. Engine performance influences were examined, especially regarding brake power, brake thermal efficiency (BTE), and brake specific fuel consumption (BSFC), in addition to the combustion characteristics like cylinder temperature and pressure. A Lotus Engine Simulation program was used for analyzing and modeling. The results demonstrated that the best performance and combustion characteristics were with mixtures that have increased in the H2 percentage. The results show that the brake power and BTE increased, and the BSFC decreased with the increase of hydrogen in the mixture. It was found that the brake power and BTE increased by 2% and 21% for HCNG 25, and the best reduction in BSFC was 6% for HCNG 20 compared to the CNG. It was also observed that maximum cylinder pressure (Pmax) and temperature (Tmax) increase with increasing percentage of H2 in the mixture.