Powder bed fusion of metals using a laser beam system (PBF-LB/M) of highly complex and filigree parts made of tool steels is becoming more important for many industrial applications and scientific investigations. To achieve high density and sufficient chemical homogeneity, pre-alloyed gas-atomized spherical powder feedstock is used. For high-performance materials such as tool steels, the number of commercially available starting powders is limited due to the susceptibility to crack formation in carbon-bearing steels. Furthermore, scientific alloy development in combination with gas-atomization is a cost-intensive process which requires high experimental effort. To overcome these drawbacks, this investigation describes the adaption of a hot work tool steel for crack-free PBF-LB/M-fabrication without any preheating as well as an alternative alloying strategy which implies the individual admixing of low-cost aspherical elemental powders and ferroalloy particles with gas-atomized pure iron powder. It is shown that the PBF-LB/M-fabrication of this powder mixture is technically feasible, even though the partly irregular-shaped powder particles reduce the flowability and the laser reflectance compared to a gas-atomized reference powder. Moreover, some high-melting alloying ingredients of the admixed powder remain unmolten within the microstructure. To analyze the laser energy input in detail, the second part of the investigation focuses on the characterization of the individual laser light reflectance of the admixed alloy, the gas-atomized reference powder and the individual alloying elements and ferroalloys.

This work aims to show the impact of the allowed chemical composition range of AISI 316L stainless steel on its processability in additive manufacturing and on the resulting part properties. ASTM A276 allows the chromium and nickel contents in 316L stainless steel to be set between 16 and 18 mass%, respectively, 10 and 14 mass%. Nevertheless, the allowed compositional range impacts the microstructure formation in additive manufacturing and thus the properties of the manufactured components. Therefore, this influence is analyzed using three different starting powders. Two starting powders are laboratory alloys, one containing the maximum allowed chromium content and the other one containing the maximum nickel content. The third material is a commercial powder with the chemical composition set in the middle ground of the allowed compositional range. The materials were processed by laser-based powder bed fusion (PBF-LB/M). The powder characteristics, the microstructure and defect formation, the corrosion resistance, and the mechanical properties were investigated as a function of the chemical composition of the powders used. As a main result, solid-state cracking could be observed in samples additively manufactured from the starting powder containing the maximum nickel content. This is related to a fully austenitic solidification, which occurs because of the low chromium to nickel equivalent ratio. These cracks reduce the corrosion resistance as well as the elongation at fracture of the additively manufactured material that possesses a low chromium to nickel equivalent ratio of 1.0. A limitation of the nickel equivalent of the 316L type steel is suggested for PBF-LB/M production. Based on the knowledge obtained, a more detailed specification of the chemical composition of the type 316L stainless steel is recommended so that this steel can be PBF-LB/M processed to defect-free components with the desired mechanical and chemical properties.

This paper examines different blends of starting materials for alloy development in the laser powder bed fusion (LPBF) process. By using blends of individual elemental, ferroalloy and carbide powders instead of a pre-alloyed gas-atomized starting powder, elaborate gas-atomization processes for the production of individual starting powders with varying alloy compositions can be omitted. In this work the model alloy Fe_3.5Si_1.5C is produced by LPBF from different blends of pure elemental, binary and ternary powders. Three powder blends were processed. The base material for all powder blends is a commercial gas-atomized Fe powder. In the first blend this Fe powder is admixed with SiC, in the second with the ternary raw alloy FeSiC and in the third with FeSi and FeC. After characterizing the powder properties and performing LPBF parameter studies for each powder blend, the microstructures and the mechanical properties of the LPBF-manufactured samples were analyzed. Therefore, investigations were carried out by scanning electron microscopy, wave length dispersive x-ray spectroscopy and micro hardness testing. It was shown that the admixed SiC dissolves completely during LPBF. But the obtained microstructure consisting of bainite, martensite, ferrite and retained austenite is inhomogeneous. The use of the lower melting ferroalloys FeSi and FeC as well as the ternary ferroalloy FeSiC leads to an increased chemical homogeneity after LPBF-processing. However, the particle size of the used components plays a decisive role for the dissolution behavior in LPBF.

Additive manufacturing is a high-potential technique that allows the production of components with almost no limitation in complexity. However, one of the main factors that still limits the laser-based additive manufacturing is a lack of processable alloys such as carbon martensitic hardenable tool steels, which are rarely investigated due to their susceptibility to cold cracking. Therefore, this study aimed to expand the variety of steels for laser powder bed fusion (L-PBF) by investigating an alternative alloying strategy for hot work tool steel powder. In this study, a comprehensive investigation was performed on the powder and L-PBF processed specimen properties and their correlation with the existing defects. Cubical specimens were created using the following two alloying strategies by means of L-PBF: conventional pre-alloyed gas-atomized powder and a mixture of gas-atomized powder with mechanically crushed pure elements and ferroalloys. The influence of the particle parameters such as morphology were correlated to the defect density and resulting quasi-static mechanical properties. Micromechanical behavior and damage evolution of the processed specimens were investigated using in situ computed tomography. It was shown that the properties of the L-PBF processed specimens obtained from the powder mixture performs equal or better compared to the specimens produced from conventional powder.

Adding copper (Cu) to titanium (Ti) alloys or Ti-6Al-4V offers the potential to tailor microstructure and material properties, but previous studies report processing challenges for Cu contents above 5 wt%. In this work, Ti-6Al-4V powder was blended with pure Cu powder to investigate in situ alloying at 10, 15, and 20 wt% Cu using laser powder bed fusion. A systematic process parameter study was conducted, using identical parameters for all compositions, to evaluate the influence of Cu content on processability, density, and microstructural evolution. High relative densities (up to 99.99 %) and homogeneous, fine-grained microstructures were achieved, demonstrating that in situ alloying with Cu contents up to 20 wt% is feasible. While 10 wt% Cu could be processed robustly under all conditions, higher Cu contents showed an increased tendency for cracks. For 15 wt% and 20 wt% Cu, at least one set of parameters for each composition yielded a dense, crack-free sample. The microstructure was analyzed in detail using SEM to investigate the markedly different morphologies, while XRD was employed to identify the formed phases, including α- and β-Ti as well as Ti₂Cu. Mechanical properties were evaluated using Vickers hardness measurements (HV1) to compare the effect of Cu additions. EDS analysis confirmed chemical homogeneity across all blends. This work highlights the potential of powder blending combined with laser powder bed fusion to explore new Ti-6Al-4V–xCu compositions beyond previously reported limits.