Celso Márquez-Sánchez

Dr. Celso Márquez-Sánchez

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 March 2016 in IEEE Latin America Transactions
Verified
Journal Article
Closed access
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
JGJosé Rafael García-Sánchez
José Rafael García-Sánchez
VHVictor Manuel Hernández-Guzmán
Victor Manuel Hernández-Guzmán
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
MAMariana Marcelino Aranda
Mariana Marcelino Aranda
In this work a three-level controller that carries out the trajectory tracking task for a differential drive wheeled mobile robot (WMR) is presented. Such a controller considers, for the first time in literature, the dynamics associated with the three subsystems that compose a WMR, i.e., mechanical structure, actuators, and power stage. The high level corresponds to an input-output linearization control for the mechanical structure; the medium level is based on two sensorless controls designed via differential flatness for the actuators; and the low level is related to two cascade controls based on sliding modes and PI control for the power stage. The performance and robustness of the controller is verified and shown via realistic simulations when parametric uncertainties associated with the subsystems that compose the WMR are considered.

1 January 2014 in Mathematical Problems in Engineering
Verified
Journal Article
Open access
PDF file
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
FCF Carrizosacorral
F Carrizosacorral
MAMayra Antonio-Cruz
Mayra Antonio-Cruz
JAJ M Albamartinez
J M Albamartinez
GSG Saldanagonzalez
G Saldanagonzalez
This paper presents a hierarchical controller that carries out the angular velocity trajectory tracking task for a DC motor driven by a DC/DC Buck converter. The high level control is related to the DC motor and the low level control is dedicated to the DC/DC Buck converter; both controls are designed via differential flatness. The high level control provides a desired voltage profile for the DC motor to achieve the tracking of a desired angular velocity trajectory. Then, a low level control is designed to ensure that the output voltage of the DC/DC Buck converter tracks the voltage profile imposed by the high level control. In order to experimentally verify the hierarchical controller performance, a DS1104 electronic board from dSPACE and Matlab‐Simulink are used. The switched implementation of the hierarchical average controller is accomplished by means of pulse width modulation. Experimental results of the hierarchical controller for the velocity trajectory tracking task show good performance and robustness against the uncertainties associated with different system parameters.

7 December 2017 in Complexity
Verified
Journal Article
Open access
PDF file
JGJosé Rafael García-Sánchez
José Rafael García-Sánchez
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
STSalvador Tavera-Mosqueda
Salvador Tavera-Mosqueda
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
VHVictor Manuel Hernández-Guzmán
Victor Manuel Hernández-Guzmán
HTHind Taud
Hind Taud
The trajectory tracking task in a wheeled mobile robot (WMR) is solved by proposing a three-level hierarchical controller that considers the mathematical model of the mechanical structure (differential drive WMR), actuators (DC motors), and power stage (DC/DC Buck power converters). The highest hierarchical level is a kinematic control for the mechanical structure; the medium level includes two controllers based on differential flatness for the actuators; and the lowest hierarchical level consists of two average controllers also based on differential flatness for the power stage. In order to experimentally validate the feasibility of the proposed control scheme, the hierarchical controller is implemented via a Σ–Δ-modulator in a differential drive WMR prototype that we have built. Such an implementation is achieved by using MATLAB-Simulink and the real-time interface ControlDesk together with a DS1104 board. The experimental results show the effectiveness and robustness of the proposed control scheme.

23 May 2023 in ISA Transactions
Verified
Journal Article
Open access
MAMayra Antonio-Cruz
Mayra Antonio-Cruz
VHVictor Manuel Hernández-Guzmán
Victor Manuel Hernández-Guzmán
CMCarlos Alejandro Merlo-Zapata
Carlos Alejandro Merlo-Zapata
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
Different works in literature have reported that nonlinear controllers based on the energy approach are not effective to completely swing-up an inverted pendulum subjected to friction. Most studies trying to solve this issue consider static friction models in the design of controllers. This consideration is mainly because the stability proof of the system with dynamic friction in closed-loop is difficult. Hence, this paper presents a nonlinear controller with friction compensation to swing-up a Furuta pendulum with dynamic friction. With this aim, we consider that only the active joint of the system is subjected to friction, which is represented via a dynamic model, namely, the Dahl model. We first present Furuta Pendulum dynamic model with dynamic friction. Then, by slightly modifying an energy-based controller that has been previously reported in literature and by including friction compensation, we propose a nonlinear controller that allows to swing-up completely a Furuta pendulum subjected to friction. The unmeasurable friction state is estimated through a nonlinear observer and a stability analysis of the closed-loop system is accomplished with the direct Lyapunov method. Finally, successful experimental results are presented for a Furuta pendulum prototype built by authors. This shows the effectiveness of the proposed controller in achieving a complete swing-up of the Furuta pendulum, in a time feasible for experimental implementation, and ensuring closed-loop stability.

24 October 2019 in Electronics
Verified
Journal Article
Open access
PDF file
EHEduardo Hernández-Márquez
Eduardo Hernández-Márquez
CACarlos Alejandro Avila-Rea
Carlos Alejandro Avila-Rea
JGJosé Rafael García-Sánchez
José Rafael García-Sánchez
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
MMMagdalena Marciano-Melchor
Magdalena Marciano-Melchor
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
A mathematical model of a new “full-bridge Buck inverter–DC motor” system is developed and experimentally validated. First, using circuit theory and the mathematical model of a DC motor, the dynamic behavior of the system under study is deduced. Later, the steady-state, stability, controllability, and flatness properties of the deduced model are described. The flatness property, associated with the mathematical model, is then exploited so that all system variables and the input can be differentially parameterized in terms of the flat output, which is determined by the angular velocity. Then, when a desired trajectory is proposed for the flat output, the input signal is calculated offline and is introduced into the system. In consequence, the validation of the mathematical model for constant and time-varying duty cycles is possible. Such a validation of this mathematical model is tackled from two directions: (1) by circuit simulation through the SimPowerSystems toolbox of Matlab-Simulink and (2) via a prototype of the system built by using Matlab-Simulink and a DS1104 board. The good similarities between the circuit simulation and the experimental results allow satisfactorily validating the mathematical model.

1 January 2013 in The Scientific World Journal
Verified
Journal Article
Open access
PDF file
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
MMMariana Marcelino-Aranda
Mariana Marcelino-Aranda
MMMagdalena Marciano-Melchor
Magdalena Marciano-Melchor
RBR. Bautista-Quintero
R. Bautista-Quintero
DMD. Muñoz-Carrillo
D. Muñoz-Carrillo
This paper reports a solution for trajectory tracking control of a differential drive wheeled mobile robot (WMR) based on a hierarchical approach. The general design and construction of the WMR are described. The hierarchical controller proposed has two components: a high‐level control and a low‐level control. The high‐level control law is based on an input‐output linearization scheme for the robot kinematic model, which provides the desired angular velocity profiles that the WMR has to track in order to achieve the desired position (x*, y*) and orientation (φ*). Then, a low‐level control law, based on a proportional integral (PI) approach, is designed to control the velocity of the WMR wheels to ensure those tracking features. Regarding the trajectories, this paper provides the solution or the following cases: (1) time‐varying parametric trajectories such as straight lines and parabolas and (2) smooth curves fitted by cubic splines which are generated by the desired data points . A straightforward algorithm is developed for constructing the cubic splines. Finally, this paper includes an experimental validation of the proposed technique by employing a DS1104 dSPACE electronic board along with MATLAB/Simulink software.