Fernando Carrizosa-Corral

Fernando Carrizosa-Corral

Auto-generated profile, based on publicly available information

Fernando Carrizosa-Corral

Dirección de Energías Centro de Ingeniería y Desarrollo Industrial Santiago de Querétaro Querétaro Mexico

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2014 in Mathematical Problems in Engineering
Verified
Journal Article
Open access
PDF file
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
FCF Carrizosacorral
F Carrizosacorral
MAMayra Antonio-Cruz
Mayra Antonio-Cruz
JAJ M Albamartinez
J M Albamartinez
GSG Saldanagonzalez
G Saldanagonzalez
This paper presents a hierarchical controller that carries out the angular velocity trajectory tracking task for a DC motor driven by a DC/DC Buck converter. The high level control is related to the DC motor and the low level control is dedicated to the DC/DC Buck converter; both controls are designed via differential flatness. The high level control provides a desired voltage profile for the DC motor to achieve the tracking of a desired angular velocity trajectory. Then, a low level control is designed to ensure that the output voltage of the DC/DC Buck converter tracks the voltage profile imposed by the high level control. In order to experimentally verify the hierarchical controller performance, a DS1104 electronic board from dSPACE and Matlab‐Simulink are used. The switched implementation of the hierarchical average controller is accomplished by means of pulse width modulation. Experimental results of the hierarchical controller for the velocity trajectory tracking task show good performance and robustness against the uncertainties associated with different system parameters.

8 September 2014
Verified
Book Chapter
Open access
PDF file
RSRamon Silva-Ortigoza
Ramon Silva-Ortigoza
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
FCFernando Carrizosa-Corral
Fernando Carrizosa-Corral
VHVictor Manuel Hernández-Guzmán
Victor Manuel Hernández-Guzmán
JGJose Rafael Garcia-Sánchez
Jose Rafael Garcia-Sánchez
JAJesús Antonio Alvarez-Cedillo
Jesús Antonio Alvarez-Cedillo
Obstacle Avoidance Task for a Wheeled Mobile Robot – A Matlab-Simulink-Based Didactic Application | InTechOpen, Published on: 2014-09-08. Authors: R. Silva-Ortigoza, C. Márquez-Sánchez, F. Carrizosa-Corral, et

26 November 2014 in Abstract and Applied Analysis
Verified
Journal Article
Open access
PDF file
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
FCF. Carrizosa-Corral
F. Carrizosa-Corral
JGJ. J. Gálvez-Gamboa
J. J. Gálvez-Gamboa
MMM. Marcelino-Aranda
M. Marcelino-Aranda
DMD. Muñoz-Carrillo
D. Muñoz-Carrillo
HTHind Taud
Hind Taud
Sliding mode control is a discontinuous control technique that is, by its nature, appropriate for controlling variable structure systems, such as the switch regulated systems employed in power electronics. However, when designing control laws based on the average models of these systems a modulator is necessary for their experimental implementation. Among the most widely used modulators in power electronics are the pulse width modulation (PWM) and, more recently, the sigma-delta-modulator (Σ-Δ-modulator). Based on the importance of achieving an appropriate implementation of average control laws and the relevance of the trajectory tracking task in DC/DC power converters, for the first time, this research presents the assessment of the experimental results obtained when one of these controllers is implemented through either a PWM or aΣ-Δ-modulator to perform such a task. A comparative assessment based on the integral square error (ISE) index shows that, at frequencies with similar efficiency, theΣ-Δ-modulator provides a better tracking performance for the DC/DC Buck converter. In this paper, an average control based on differential flatness was used to perform the experiments. It is worth mentioning that a different trajectory tracking controller could have been selected for this research.

7 August 2018 in International Journal of Circuit Theory and Applications
Verified
Journal Article
Closed access
FCFernando Carrizosa‐Corral
Fernando Carrizosa‐Corral
AVAlberto Vazquez-Cervantes
Alberto Vazquez-Cervantes
JMJosue Rafael Montes Martínez
Josue Rafael Montes Martínez
KHKarla-Teresa Hernández-Díaz
Karla-Teresa Hernández-Díaz
JVJulio César Solano Vargas
Julio César Solano Vargas
Hugo Jimenez HernandezHugo Jimenez Hernandez
Hugo Jimenez Hernandez

1 November 2016
Verified
Conference Paper
Closed access
RORoberto Antonio Orozco-Velazquez
Roberto Antonio Orozco-Velazquez
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
JGJosé Rafael García-Sánchez
José Rafael García-Sánchez
HTHind Taud
Hind Taud
FCFernando Carrizosa-Corral
Fernando Carrizosa-Corral
This work presents the design of a wheeled mobile robot (WMR) using an Ackerman configuration. Its design uses the extruded aluminum profile widely used in industry, facilitating the assembly of new robotics projects. The design is carried out using CAD software and shows some of the various benefits of these tools. The environmental impact values for a bar of extruded aluminum profile throughout its lifecycle was calculated and, later, analyzed by using SolidWorks simulationXpress study to improve the sustainability of the WMR design. Additionally, images of both the 3D model and the real prototype are presented.

1 November 2014
Verified
Conference Paper
Closed access
ROR.A. Orozco-Velazquez
R.A. Orozco-Velazquez
RSRAMON SILVA-ORTIGOZA
RAMON SILVA-ORTIGOZA
HTHind Taud
Hind Taud
MAMayra Antonio-Cruz
Mayra Antonio-Cruz
CMCelso Márquez-Sánchez
Celso Márquez-Sánchez
FCF. Carrizosa-Corral
F. Carrizosa-Corral
The present paper addresses the design and construction stages of a skid steer wheeled mobile robot (WMR) configuration. The pieces employed in the WMR were designed to be compatible with the extruded aluminium profile widely used in industry, facilitating subsequent WMRs designs. The pieces were designed using Solid Works and, later, simulated via Solid Works Simulation software. Additionally, images of both the 3D model and the real prototype are shown.