A novel flexible nanocomposite pressure sensor with a tensile strength of about 47 MPa is fabricated in this work. Nanolayers of titanium dioxide (titania nanolayers, TNL) synthesized by hydrothermal method are used to reinforce the polyvinylidene fluoride (PVDF) by simple solution mixing. A hybrid composite is prepared by incorporating the TNL (2.5 wt %) with reduced graphene oxide (rGO) (2.5 wt %) synthesized by improved graphene oxide synthesis to form a PVDF/rGO-TNL composite. A comparison between PVDF, PVDF/rGO (5 wt %), PVDF/TNL (5 wt %) and PVDF/rGO-TNL (total additives 5 wt %) samples are analyzed for their sensing, thermal and dielectric characteristics. The new shape of additives (with sharp morphology), good interaction and well distributed hybrid additives in the matrix increased the sensitivity by 333.46% at 5 kPa, 200.7% at 10.7 kPa and 246.7% at 17.6 kPa compared to the individual PVDF composite of TNL, confirming its possible application in fabricating low cost and light weight pressure sensing devices and electronic devices with reduced quantity of metal oxides. Increase in the β crystallinity percentage and removal of α phase for PVDF was detected for the hybrid composite and linked to the improvement in the mechanical properties. Tensile strength for the hybrid composite (46.91 MPa) was 115% higher than that of the neat polymer matrix. Improvement in the wettability and less roughness in the hybrid composites were observed, which can prevent fouling, a major disadvantage in many sensor applications.
1 June 2017 in Materials Science and Engineering: R: Reports
Carboxyl-terminated (butadiene-co-acrylonitrile) (CTBN) modified epoxy/clay nanocomposites (epoxy/clay/CTBN ternary nanocomposites) were synthesized using nadic methyl anhydride as curing agent. Effect of nanoclay on the phase behavior (UCST) of epoxy oligomer/CTBN blend has been studied in detail. The phase diagram was shifted to a higher temperature with increase in clay loading due to the easy penetration of low molecular weight CTBN into the clay galleries. The XRD studies confirmed the penetration of CTBN into the clay galleries, as the ‘d’ spacing increased with increase in CTBN content in the epoxy/clay/CTBN ternary nanocomposite. The interaction of organically modified clay with epoxy and CTBN were studied using frequency sweep rheological analysis. The individual and combined effect of nanoclay and CTBN on the cure reaction was followed by isothermal rheological analysis. It was found that complex viscosity profiles during cure reaction follow an exponential growth. The characteristic relaxation time of viscosity growth was described by the WLF equation. Moreover the dynamics of phase separation during cure was followed using optical microscopy. The scanning electron microscopic (SEM) images revealed that the domain size of phase separated CTBN in epoxy/clay/CTBN ternary nanocomposite was smaller than in epoxy/CTBN binary blend. The kinetic factor in epoxy-anhydride cure reaction and the presence of clay at epoxy–CTBN interface was used to explain this size reduction. The high resolution transmission electron microscopic (HRTEM) image of epoxy/3 phr clay nanocomposite showed that the clay platelets were mostly intercalated. Epoxy/3 phr clay/15 phr CTBN nanocomposite has an intercalated with occasional exfoliated microstructure with slightly distorted clay orientation. Low magnification TEM images showed that most of the clay platelets located near the phase separated CTBN and the presence of clay at the epoxy–CTBN interface. The viscoelastic properties of epoxy/clay/CTBN nanocomposite was studied and compared with that of epoxy/clay nanocomposite and epoxy/CTBN blend. A quantitative measurement of constrained region (macromolecular chains immobilized by the clay platelets) was carried out for epoxy/clay and epoxy/clay/CTBN nanocomposites. Finally thermal degradation studies were performed to evaluate the thermal stability of the ternary nanocomposites.
1 September 2015 in Composites Science and Technology
The use of self-healing coatings to protect metal substrates, such as aluminum alloys, stainless steel, carbon steel, and Mg alloys from corrosion is an important aspect for protecting metals and for the economy. During the past decade, extensive transformations on self-healing strategies were introduced in protective coatings, including the use of green components. Scientists used extracts of henna leaves, aloe vera, tobacco, etc. as corrosion inhibitors, and cellulose nanofibers, hallyosite nanotubes, etc. as healing agent containers. This review gives a concise description on the need for self-healing protective coatings for metal parts, the latest extrinsic self-healing strategies, and the techniques used to follow-up the self-healing process to control the corrosion of metal substrates. Common techniques, such as accelerated salt immersion test and electrochemical impedance spectroscopy (EIS), for evaluating the self-healing process in protective coatings are explained. We also show recent advancements procedures, such as scanning vibrating electrode technique (SVET) and scanning electrochemical microscopy (SECM), as successful techniques in evaluating the self-healing process in protective coatings.