Elia Brescia

Dr. Elia Brescia

Politecnico di Bari
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 September 2020 in Energies
Verified
Journal Article
Open access
PDF file
DCDiego Calabrese
Diego Calabrese
Gioacchino TricaricoGioacchino Tricarico
Gioacchino Tricarico
Elia BresciaElia Brescia
Elia Brescia
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
VMVito Giuseppe Monopoli
Vito Giuseppe Monopoli
FCFrancesco Cupertino
Francesco Cupertino
This paper proposes a new variable structure control scheme for a variable-speed, fixed-pitch ducted wind turbine, equipped with an annular, brushless permanent-magnet synchronous generator, considering a back-to-back power converter topology. The purpose of this control scheme is to maximise the aerodynamic power over the entire wind speed range, considering the mechanical safety limits of the ducted wind turbine. The ideal power characteristics are achieved with the design of control laws aimed at performing the maximum power point tracking control in the low wind speeds region, and the constant speed, power, and torque control in the high wind speed region. The designed control laws utilize a Luenberger observer for the estimation of the aerodynamic torque and a shallow neural network for wind speed estimation. The effectiveness of the proposed method was verified through tests in a laboratory setup. Moreover, a comparison with other solutions from the literature allowed us to better evaluate the performances achieved and to highlight the originality of the proposed control scheme.

29 March 2021 in Energies
Verified
Journal Article
Open access
PDF file
Elia BresciaElia Brescia
Elia Brescia
DCDonatello Costantino
Donatello Costantino
PMPaolo Roberto Massenio
Paolo Roberto Massenio
VMVito Giuseppe Monopoli
Vito Giuseppe Monopoli
FCFrancesco Cupertino
Francesco Cupertino
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
Permanent magnet machines with segmented stator cores are affected by additional harmonic components of the cogging torque which cannot be minimized by conventional methods adopted for one-piece stator machines. In this study, a novel approach is proposed to minimize the cogging torque of such machines. This approach is based on the design of multiple independent shapes of the tooth tips through a topological optimization. Theoretical studies define a design formula that allows to choose the number of independent shapes to be designed, based on the number of stator core segments. Moreover, a computationally-efficient heuristic approach based on genetic algorithms and artificial neural network-based surrogate models solves the topological optimization and finds the optimal tooth tips shapes. Simulation studies with the finite element method validates the design formula and the effectiveness of the proposed method in suppressing the additional harmonic components. Moreover, a comparison with a conventional heuristic approach based on a genetic algorithm directly coupled to finite element analysis assesses the superiority of the proposed approach. Finally, a sensitivity analysis on assembling and manufacturing tolerances proves the robustness of the proposed design method.

5 July 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Open access
Elia BresciaElia Brescia
Elia Brescia
PMPaolo Roberto Massenio
Paolo Roberto Massenio
MNMauro Di Nardo
Mauro Di Nardo
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
CGChristopher Gerada
Christopher Gerada
FCFrancesco Cupertino
Francesco Cupertino
This paper proposes a nonintrusive parameter identification procedure suitable for Internet-of-Things (IoT)-embedded isotropic permanent magnet synchronous machines (PMSM). The method is designed for scenarios where only measurements collected without additional sensors, dedicated tests or signal injection from in-service off-the-shelves motor drives are available. After the automatic detection of the steady state operating conditions defined by the triplet current-speed-temperature, the rotor flux linkage, the stator resistance, the inductance, and the inverter distorted voltage term are estimated using two operating points. Particular emphasis is placed in defining the criteria of selecting these two optimal operating conditions to minimize the estimation errors. The latter are due to the inevitable difference between the parameters in different operating points. As a vessel to investigate the effectiveness of the proposed parameter identification, experimental and simulation tests carried out on a high-speed PMSM drive have been used for validation purpose. The proposed method is also compared with existing methods from the literature to demonstrate its superiority in the considered scenario.

9 July 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Elia BresciaElia Brescia
Elia Brescia
DCDonatello Costantino
Donatello Costantino
FMFederico Marzo
Federico Marzo
PMPaolo Roberto Massenio
Paolo Roberto Massenio
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
DNDavid Naso
David Naso
Parameter identification of permanent magnet synchronous machines (PMSMs) represents a well-established research area. However, parameter estimation of multiple running machines in large-scale applications has not yet been investigated. In this context, a flexible and automated approach is required to minimize complexity, costs, and human interventions without requiring machine information. This paper proposes a novel identification strategy for surface PMSMs (SPMSMs), highly suitable for large-scale systems. A novel multistep approach using measurement data at different operating conditions of the SPMSM is proposed to perform the parameter identification without requiring signal injection, extra sensors, machine information, and human interventions. Thus, the proposed method overcomes numerous issues of the existing parameter identification schemes. An IoT/cloud architecture is designed to implement the proposed multistep procedure and massively perform SPMSM parameter identifications. Finally, hardware-in-the-loop results show the effectiveness of the proposed approach.

23 August 2020
Verified
Conference Paper
Closed access
Elia BresciaElia Brescia
Elia Brescia
MPM. Palmieri
M. Palmieri
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
FCF. Cupertino
F. Cupertino
This paper proposes an innovative design method for the cogging torque suppression of permanent magnet machines with a segmented stator core. This method is based on the design of the shape of the stator tooth tips through a quasi-binary optimization using a genetic algorithm and iterative finite element analysis. The method has been applied to an annular permanent magnet synchronous machine with a segmented stator core for a low power wind generator. The solutions achieved by the optimization have been validated through accurate finite element analysis. The optimized machine shows a reduction of the cogging torque by 94% in comparison with the basic one.

8 April 2021
Verified
Conference Paper
Closed access
DCDonatello Costantino
Donatello Costantino
Elia BresciaElia Brescia
Elia Brescia
PMPaolo Roberto Massenio
Paolo Roberto Massenio
PSPietro Serafino
Pietro Serafino
Giuseppe Leonardo CascellaGiuseppe Leonardo Cascella
Giuseppe Leonardo Cascella
FCFrancesco Cupertino
Francesco Cupertino
This paper proposes an innovative Supervised model Reference Adaptive System (SuMRAS) for the rotor flux linkage identification in Surface Permanent Magnet Synchronous Machines (SPMSM). Estimations are updated in an autonomous way when convergence is reached. The proposed SuMRAS can be applied also to operating motors without requiring manual analysis, hence, it is suitable for large-scale implementation in cloud services. The effectiveness of the proposed approach is assessed in a real-world cloud environment through hardware-in-the-loop (HIL) experiments.