Francisca Cabrera-Covarrubias

Dr. Francisca Cabrera-Covarrubias

UNIVERSIDAD AUTONOMA DE SINALOA
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 December 2016 in Materials
Verified
Journal Article
Open access
PDF file
Francisca Cabrera-CovarrubiasFrancisca Cabrera-Covarrubias
Francisca Cabrera-Covarrubias
José Manuel Gómez-SoberónJosé Manuel Gómez-Soberón
José Manuel Gómez-Soberón
Jorge Almaral-SánchezJorge Almaral-Sánchez
Jorge Almaral-Sánchez
SRSusana Paola Arredondo Rea
Susana Paola Arredondo Rea
MSMaría Consolación Gómez Soberón
María Consolación Gómez Soberón
Ramón Corral HigueraRamón Corral Higuera
Ramón Corral Higuera
The difficult current environmental situation, caused by construction industry residues containing ceramic materials, could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore, this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0%, 10%, 20%, 30%, 50% and 100%), such as the density and compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analytical process of the results in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content) are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness. At the end of the investigation, it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the obtained prediction equations could be used in cases of similar applications.

14 February 2017 in Materials
Verified
Journal Article
Open access
PDF file
JMJosé Miguel Mendivil-Escalante
José Miguel Mendivil-Escalante
José Manuel Gómez-SoberónJosé Manuel Gómez-Soberón
José Manuel Gómez-Soberón
Jorge Almaral-SánchezJorge Almaral-Sánchez
Jorge Almaral-Sánchez
Francisca Cabrera-CovarrubiasFrancisca Cabrera-Covarrubias
Francisca Cabrera-Covarrubias
In the field of construction, sustainable building materials are currently undergoing a process of technological development. This study aims to contribute to understanding the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate a polyethylene terephthalate (PET)-based additive in their matrix (produced by synthesis and glycolysis of recycled PET bottles) in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity, Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1%, 3%, 4%, 5%, 7% and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation with other physical and mechanical properties are also explained.

13 September 2020 in Minerals
Verified
Journal Article
Open access
PDF file
TMT. J. Medina
T. J. Medina
SRSusana Paola Arredondo Rea
Susana Paola Arredondo Rea
Ramón Corral HigueraRamón Corral Higuera
Ramón Corral Higuera
AJAraceli Jacobo-Azuara
Araceli Jacobo-Azuara
RZR. A. Zárraga
R. A. Zárraga
JBJesús Manuel Bernal-Camacho
Jesús Manuel Bernal-Camacho
In this study, a blast furnace slag (BFS) and fly ash (FA) based adsorbent geopolymer to be used for removing Pb2+ from aqueous solutions were synthesized using the hydrothermal method at 60 °C for 24 h, and then cured at 25 °C for another six days. The alkali activator applied in this work was a combination of sodium hydroxide and sodium silicate solutions at a mass ratio of 2. The geopolymer slurry was adjusted to a Si/Al molar ratio of 3. A BFS-based geopolymer (GS) having a specific area of 23.56 m2/g and pore size and volume of 7.8 nm and 73 cm3/kg, respectively, surpassed the raw material surface by approximately 13-fold. An FA-based geopolymer (GA) having a specific area of 35.97 m2/g and a size and porous volume of 9 nm and 124 nm, respectively, surpassed the raw material surface by approximately 23-fold. In addition, GS and GA showed a cation exchange capacity (CEC) of 241.30 and 286.96 Meq/100 g, respectively. X-ray diffraction (XRD) determined sample crystallinity and it was proven by scanning electron microscopy (SEM), showing that both geopolymers were constituted of unreacted particles surrounded by amorphous and semi-amorphous products. Through Fourier transform infrared spectroscopy (FTIR), a band that was assigned to the asymmetric stretching vibration of Si-O-M (M = Na+ and/or Ca2+) non-bridging oxygen type was observed, which suggested that Na and Ca could serve as exchangeable ions in the ionic exchange process. Adsorption test data indicated that good adsorption was obtained when a neutral pH was used at room temperature, and the adsorption isotherm showed that GA had more adsorption sites than GS, which meant greater maximum adsorption capacity.

1 December 2015 in Revista de la construcción
Verified
Journal Article
Open access
PDF file
Francisca Cabrera-CovarrubiasFrancisca Cabrera-Covarrubias
Francisca Cabrera-Covarrubias
SRSusana Paola Arredondo Rea
Susana Paola Arredondo Rea
José Manuel Gómez-SoberónJosé Manuel Gómez-Soberón
José Manuel Gómez-Soberón
Jorge Almaral-SánchezJorge Almaral-Sánchez
Jorge Almaral-Sánchez
Ramón Corral HigueraRamón Corral Higuera
Ramón Corral Higuera
We study the behavior of mortars where 0%, 10%, 20%, 30%, 50% and 100% of their original natural sand was replaced by ceramic sand in a search of potential new building materials that will help to conserve natural resources and that are environmentally friendly. In this paper, the physical properties of the sands and their derived mortars, including their compressive strength, flexural strength, and shrinkage due to base and total drying, are characterized. Our results show that the compressive and flexural strengths of the recycled mortars decrease proportionally to the amount of natural sand replacement used. A similar behavior is observed for the shrinkage due to drying in mortars with low ceramic substitutions (10%, 20% and 30%). Based on these findings, we believe that the use of mortars made with recycled sand (with substitution contents lower than 30%) could be feasible in applications where the mechanical requirements are low.

12 August 2022 in Polymers
Verified
Journal Article
Open access
PDF file
ABA. Bórquez-Mendivil
A. Bórquez-Mendivil
AHAbel Hurtado-Macias
Abel Hurtado-Macias
Jesus Eduardo Leal-PerezJesus Eduardo Leal-Perez
Jesus Eduardo Leal-Perez
JFJ. Flores-Valenzuela
J. Flores-Valenzuela
RVRamón Álvaro Vargas-Ortíz
Ramón Álvaro Vargas-Ortíz
Jorge Almaral-SánchezJorge Almaral-Sánchez
Jorge Almaral-Sánchez
Hybrid coatings of SiO2 and recycled unsaturated polyester resin (R-UPR) from recycled polyethylene-terephthalate (PET) were prepared by the sol-gel process on glass substrates. First, SiO2 was synthesized by the sol-gel process using a tetraethyl orthosilicate (TEOS) solution. Next, bis(2-hydroxypropyl-terephthalate) (BHPT) was synthesized from mechanical and chemical recycling (glycolysis) of post-consumer PET bottles in propylene glycol (PG) using ZnA as catalyst, in a Vessel-type reactor (20–200 °C); maleic anhydride (MA) was added and, following the same procedure, the unsaturated polyester (UP) was synthetized, which was cooled to room temperature. Next, styrene (St) and benzoyl-peroxide (PBO)-initiator were added to obtain R–UPR. TEOS (T) and three hybrid solutions were synthesized, with molar ratios of 0:1:0 (T), 1:2:0.25 (H1), 1:1:0.25 (H2), and 1:0:0.25 (H3) for R–UPR:TEOS:3-trimethoxy-(silyl)-propyl-methacrylate (TMSPM), respectively, with which TC, HC1, HC2, and HC3 coatings were elaborated using the immersion technique and polymerized (120 °C for 24 h). The solutions were characterized by FT–IR and TGA, and the coatings by SEM, nanoindentation, AFM, adhesion, and contact angle. The results showed that SiO2 enhanced mechanical (hardness and Young’s modulus) and thermal properties of the R-UPR. The coatings adhered perfectly to the substrate, with thicknesses of micrometer units and a flat surface; in addition, hydrophilicity decreased as SiO2 decreased.

28 November 2016 in Preprints.org
Verified
Preprint
Open access
PDF file
Francisca Cabrera-CovarrubiasFrancisca Cabrera-Covarrubias
Francisca Cabrera-Covarrubias
José Manuel Gómez-SoberónJosé Manuel Gómez-Soberón
José Manuel Gómez-Soberón
Jorge Almaral-SánchezJorge Almaral-Sánchez
Jorge Almaral-Sánchez
SRSusana Paola Arredondo Rea
Susana Paola Arredondo Rea
MSMaría Consolación Gómez Soberón
María Consolación Gómez Soberón
Ramón Corral HigueraRamón Corral Higuera
Ramón Corral Higuera
The difficult current environmental situation, caused by construction industry residues containing ceramic materials could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0, 10, 20, 30, 50 and 100%), such as: the density, the compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analysis process of the results are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness; in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content). At the end of the investigation it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the prediction equations produced could be used in cases of similar applications.