This paper characterizes the static, dynamic, and controlled behavior of a high-performance electro-hydraulic actuator to assess its suitability for use in evaluating machine tool behavior. The actuator consists of a double-acting piston and cylinder arrangement controlled by a servo valve and a separate rear chamber controlled by a separate valve, designed to work in conjunction to generate static forces of up to 7000 N that can be superposed with dynamic forces of up to ±1500 N. This superposition of periodic forces with a non-zero mean makes the actuator capable of applying realistic loading conditions like those experienced by machines during cutting processes. To characterize the performance of this actuator, linearized static and dynamic models are described. Since experiments with the actuator exhibit nonlinear characteristics, the linearized static model is expanded to include the influence of nonlinearities due to flow, leakages, saturations, and due to friction and hysteresis. Since all major nonlinearities are accounted for in the expanded static model, the dynamical model remains linear. Unknown static and dynamical model parameters are calibrated from experiments, and the updated models are observed to capture experimentally observed behavior very well. Validated models are used to tune the proportional and integral gains for the closed-loop control strategy, and the model-based tuning in turn guides appropriate closed-loop control of the actuator to increase its bandwidth to 200 Hz. The statically and dynamically characterized actuator can aid machine tool structural testing. Moreover, the validated models can instruct the design and development of other higher-performance electro-hydraulic actuators, guide the conversion of the actuator into a damper, and also test other advanced control strategies to further improve actuator performance.
1 May 2020 in CIRP Journal of Manufacturing Science and Technology
Industrial robots are increasingly prevalent due to their large workspace and cost-effectiveness. However, their limited static and dynamic stiffness can lead to issues like mode coupling chatter and regenerative chatter in robotic milling processes, even at shallow cutting depths. These problems significantly impact performance, product quality, tool longevity, and can damage robot components. An active inertial actuator was deployed at the milling spindle to enhance dynamic stiffness and suppress low-frequency vibrations effectively. It was identified that the characteristics of the actuator change with its mounting orientation, a common scenario in robotic machining processes. This variation has not been reported in the literature. Our study includes the identification of model parameters for the actuator in both horizontal and vertical mountings. Additionally, the novelty of the present work lies in the specific design and implementation of compensation filters tailored for the active inertial actuator in both horizontal and vertical configurations. These filters address the unique challenges posed by low-frequency vibrations in robotic milling, offering significant improvements in dynamic stiffness and vibration suppression. Traditional model-based compensators were effective for vertical mounting, while pole-zero placement techniques with minimum phase systems were optimal for horizontal mounting. These compensators significantly enhanced dynamic stiffness, reducing maximum low-frequency robot structural modes by approximately 100% in horizontal mounting and approximately 214% in the vertical configuration of the actuator. This advancement promises to enhance industrial robot capabilities across diverse machining applications.
22 October 2024 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
This paper presents the effect of shell element formulations on the response parameters of incremental sheet metal forming process. In this work, computational time, profile prediction and thickness distribution are investigated by both finite element analysis and experimentally. The experimental results show that the thickness distribution is in good agreement with the results obtained with Belytschko-Tsay (BT) and Improved Flanagan-Belytschko (IFB) shell element formulations. These two shell element formulations do trade-off between computational time and accuracy. For more accurate results, the BT shell element formulation is better and for less computational time with good results, the IFB shell element is preferable. Finally, BT shell element formulation has been chosen for FE Analysis of ISF process in HyperWorks, since the results of thickness distribution and profile prediction is in better agreement with the experimental results as well as the computational time is less among the shell elements.
16 December 2021 in Journal of Vibration and Control
Interruptions in turning make the process forces non-smooth and nonlinear. Smooth nonlinear cutting forces result in the process of being stable for small perturbations and unstable for larger ones. Re-entry after interruptions acts as perturbations making the process exhibit bistabilities. Stability for such processes is characterized by Hopf bifurcations resulting in lobes and period-doubling bifurcations resulting in narrow unstable lenses. Interrupted turning remains an important technological problem, and since experimentation to investigate and mitigate instabilities are difficult, this paper instead emulates these phenomena on a controlled hardware-in-the-loop simulator. Emulated cutting on the simulator confirms that bistabilities persist with lobes and lenses. Cutting in bistable regimes should be avoided due to conditional stability. Hence, we demonstrate the use of active damping to stabilize cutting with interruptions/perturbations. To stabilize cutting with small/large perturbations, we successfully implement an adaptive gain tuning scheme that adapts the gain to the level of interruption/perturbation. To facilitate real-time detection of instabilities and their control, we characterize the efficacy of the updating scheme for its dependence on the time required to update the gain and for its dependence on the levels of gain increments. We observe that higher gain increments with shorter updating times result in the process being stabilized quicker. Such results are instructive for active damping of real processes exhibiting conditional instabilities prone to perturbations.