Integrated photonic systems require fast modulators to keep up with demanding operation speeds and increasing data rates. The silicon nitride integrated photonic platform is of particular interest for applications such as datacom, light detection and ranging (LIDAR), quantum photonics, and computing owing to its low losses and CMOS compatibility. Yet, this platform inherently lacks high-speed modulators. Heterogeneous integration of lithium niobate on silicon nitride waveguides can address this drawback with its strong Pockels effect. We demonstrate the first high-speed lithium niobate modulator heterogeneously integrated on silicon nitride using micro-transfer printing. The device is 2 mm long with a half-wave voltage Vπ of 14.8 V. The insertion loss and extinction ratio are 3.3 and 39 dB, respectively. Operation beyond 50 GHz has been demonstrated with the generation of open eye diagrams up to 70 Gb/s. This proof-of-principle demonstration opens up possibilities for more scalable fabrication of these trusted and performant devices.

A cost-effective, compact and high-performance antenna element for beamforming applications in all 5G New Radio bands in the [24.25-29.5] GHz spectrum is proposed. The novel antenna topology adopts a square patch, an edge-plated air-filled cavity, and an hourglass-shaped aperture-coupled feed to achieve a very high efficiency over a wide frequency band in a compact footprint ${(0.48\lambda_{0}\times0.48\lambda_{0})}$ . Its compliance with standard PCB fabrication technology, without complex multi-layer PCB stack, ensures low-cost fabrication. The antenna feedplane offers a platform for compact integration of active electronic circuitry. Two different modular 1×4 antenna arrays were realized to demonstrate its suitability for broadband multi-antenna systems. Measurements of the fabricated antenna element and the antenna array prototypes revealed a -10-dB impedance bandwidth of 7.15 GHz (26.8%) and 8.2 GHz (30.83%), resp. The stand-alone antenna features a stable peak gain of 7.4±0.6 dBi in the [24.25- 29.5] GHz band and a measured total efficiency of at least 86%. The 1±4 array features a peak gain of 10.1±0.7 dBi and enables grating-lobe-free beamsteering from -50° to 50°.

Transceivers based on electroabsorption modulators (EAM) are considered as a promising candidate for the next generation 400 GbE short-reach optical networks. They are capable of combining high bandwidth and low-power operation with a very compact layout, removing the need for traveling wave electrodes and dedicated 50 Ω termination. In this paper, we demonstrate the first silicon-based EAM, in combination with an in-house developed SiGe BiCMOS transceiver chipset, capable of transmitting single-lane 100 Gb/s non-return-to-zero in real-time. Transmission over 500 m of standard single mode fiber and 2 km of nonzero dispersion shifted fiber is demonstrated, assuming a forward-error coding scheme is used with a bit-error ratio limit of 3.8 × 10 ^-3 . Due to the high line rate, transmission over longer fiber spans was limited by the chromatic distortion in the fiber. As a possible solution, electrical duobinary modulation is proposed as it is more resilient to this type of fiber distortion by reducing the required optical bandwidth. We show improved performance for longer fiber spans with a 100 Gb/s electrical duobinary link, resulting in realtime sub-forward error coding operation over more than 2 km of standard single-mode fiber without any digital signal processing. Finally, the possibility of a 100 Gb/s EAM-to-EAM link is investigated.

All-digital radio-over-fiber (RoF) transmission has attracted a significant amount of interest in digital-centric systems or centralized networks because it greatly simplifies the front-end hardware by using digital processing. The sigma-delta modulator (SDM)-based all-digital RoF approach pushes the digital signal processing as far as possible into the transmit chain. We present a real-time 100-GS/s fourth-order single-bit SDM for all-digital RoF transmission in the high-frequency band without the aid of analog/optical up-conversion. This is the fastest sigma-delta modulator reported and this is also the first real-time demonstration of sigma-delta modulated RoF in the frequency band above 24 GHz. 4.68 Gb/s (2.34 Gb/s) 64-QAM is transported over 10-km standard single-mode fiber in the C-band with 6.46% (4.73%) error vector magnitude and 3.13 Gb/s 256-QAM can be even received in an optical back-to-back configuration. The carrier frequency can be digitally tuned at run-time, covering a wide frequency range from 22.75 GHz to 27.5 GHz. Besides, this high-speed sigma-delta modulator introduces less than 1 μs latency in the transmit chain. Its all-digital nature enables network virtualization, making the transmitter compatible with different existing standards. The prominent performance corroborates the strong competitiveness of this SDM-based RoF approach in high-frequency radio-over-fiber 5G communication.

A new high-speed delta-sigma modulator (DSM) topology is proposed by cascading a bit reduction process with a multi-stage noise shaping MASH-1-1 DSM. This process converts the two-bit output sequence of the MASH-1-1 DSM to a single-bit sequence, merely compromising the DSM noise-shaping performance. Furthermore, the high clock frequency requirements are significantly relaxed by using parallel processing. This DSM topology facilitates the design of e.g. wideband software defined radio (SDR) transmitters and delta-sigma radio-over-fiber transmitters. Experimental results of the FPGA implementation show that the proposed low-pass DSM can operate at 21 GS/s, providing 520 MHz baseband bandwidth with 42.76 dB signal-to-noise-and-distortion ratio (SNDR) or 1.1 GHz bandwidth with 32.04 dB SNDR (based on continuous wave measurements). An all-digital transmitter based on this topology can generate 218.75 MBd 256-QAM over 200 m OM4 multimode fiber in real-time, with 7-GS/s sampling rate and an error vector magnitude below 1.89%.

To achieve the massive device connectivity and high data rate demanded by 5G, wireless transmission with wider signal bandwidths and higher-order multiple-input multiple-output (MIMO) is inevitable. This work demonstrates a possible function split option for the next generation fronthaul interface (NGFI). The proof-of-concept downlink architecture consists of real-time sigma-delta modulated signal over fiber (SDoF) links in combination with distributed multi-user (MU) MIMO transmission. The setup is fully implemented using off-the-shelf and in-house developed components. A single SDoF link achieves an error vector magnitude (EVM) of 3.14% for a 163.84 MHz-bandwidth 256-QAM OFDM signal (958.64 Mbps) with a carrier frequency around 3.5 GHz transmitted over 100-m OM4 multi-mode fiber at 850 nm using a commercial QSFP module. The centralized architecture of the proposed setup introduces no frequency asynchronism among remote radio units. For most cases, the 2×2 MU-MIMO transmission has little performance degradation compared to SISO, 0.8 dB EVM degradation for 40.96 MHz-bandwidth signals and 1.4 dB for 163.84 MHz-bandwidth on average, implying that the wireless spectral efficiency almost doubles by exploiting spatial multiplexing. A 1.4 Gbps data rate (720 Mbps per user, 163.84 MHz-bandwidth, 64-QAM) is reached with an average EVM of 6.66%. The performance shows that this approach is feasible for the high-capacity hot-spot scenario.