Igor Suminov

Prof. Igor Suminov

Moscow State Technological University "STANKIN", Moscow, 127994
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 October 2021 in Metals
Verified
Journal Article
Open access
PDF file
AAAndrey Apelfeld
Andrey Apelfeld
ABAnantoly Borisov
Anantoly Borisov
IDIlya Dyakov
Ilya Dyakov
Sergey GrigorievSergey Grigoriev
Sergey Grigoriev
BKBoris Krit
Boris Krit
ITIvan Vladimirovich Tambovskiy
Ivan Vladimirovich Tambovskiy
The influence of technological parameters of plasma electrolytic nitriding and polishing on the wear resistance and corrosion resistance of medium-carbon steel is considered. The morphology and roughness of the surface, phase composition and microhardness of the modified layer have been investigated. Wear resistance was studied under dry friction conditions with bearing steel as counter-body. It was found that plasma electrolytic polishing removes the loose part of the oxide layer and provides a two-fold decrease in surface roughness compared with untreated steel, and 2.8 times compared with the nitrided one. Combined processing at optimal technological parameters leads to an increase in microhardness up to 1130 HV, an increase in wear resistance by 70 times, and a decrease in the corrosion current density by almost 3 times in comparison with untreated steel.

21 October 2022 in Metals
Verified
Journal Article
Open access
PDF file
ITIvan Vladimirovich Tambovskiy
Ivan Vladimirovich Tambovskiy
TMTatiana Mukhacheva
Tatiana Mukhacheva
ИСИлья Горохов Илья Сергеевич
Илья Горохов Илья Сергеевич
Igor SuminovIgor Suminov
Igor Suminov
SSSergey Silkin
Sergey Silkin
Sergey GrigorievSergey Grigoriev
Sergey Grigoriev
The possibility of using an aqueous non-toxic electrolyte of ammonium nitrate and glycerin for the cathodic plasma electrolytic nitrocarburizing of low-carbon steel is considered in this paper. Surface morphology and roughness, element and phase compositions, and microhardness of the modified layer were investigated. Kinetic calculations of the processes of nitrogen and carbon diffusion into the steel surface are proposed, taking into account their mutual influence. Wear resistance was studied under dry friction conditions with tool alloy steel as a counter-body. Corrosion studies are performed using potentiodynamic polarization curves in 3.5% sodium chloride solution. The plasma electrolytic nitrocarburizing in an aqueous electrolyte with ammonium nitrate and glycerin is established to increase surface hardness up to 980 HV due to the formation of a nitrocarburized layer with 1.35 ± 0.12% carbon and 0.32 ± 0.08% nitrogen concentration. The influence of erosion in electrolyte plasma and high-temperature oxidation on the morphology and surface roughness is shown. The presence of a dense oxide layer, low surface roughness, and high hardness of the diffusion layer favor a decrease in the friction coefficient by 1.3 times, weight wear by 1.8 times and corrosion current density by 1.4 times.

12 November 2021 in Journal of Engineering Materials and Technology
Verified
Journal Article
Closed access
PDF file
Sergey GrigorievSergey Grigoriev
Sergey Grigoriev
IKI. O. Kondratsky
I. O. Kondratsky
BKBoris Krit
Boris Krit
VLV. B. Ludin
V. B. Ludin
VMV. M. Medvetskova
V. M. Medvetskova
RWR. Z. Wu
R. Z. Wu
Magnesium alloys are now widely used for various purposes due to their unique properties despite the significant disadvantage associated with low corrosion resistance. The plasma-electrolytic oxidation (PEO), which allows the formation of ceramic coatings on the surface of magnesium alloys, is the most advanced and effective method for their protection. But first, PEO process of magnesium alloys has some difficulties, and second, PEO coatings affect the thermophysical characteristics of the modified materials; in particular, they reduce thermal diffusivity. The presented work is devoted to the development of the technological parameters for formation of protective coating on the ultralight alloy Mg–8Li–1Al–0.6Ce–0.3Y by the PEO method. The results analyses of electrolytes acidity and specific electrical conductivity before and after PEO process and also investigation data of the coatings structure and surface morphology are presented. An integral assessment of the ability of thermal diffusivity and corrosion resistance of the modified alloy was made. Studying of protective and thermophysical characteristics of the obtained coating showed that it provides a sufficiently high corrosion protection, despite the relatively small thickness, and the presence of pores and slightly (not more than 5%) reduces the thermal diffusivity of the magnesium ultralight alloy.

29 September 2022 in Metals
Verified
Journal Article
Open access
PDF file
TMTatiana Mukhacheva
Tatiana Mukhacheva
SKSergei Aleksandrovich Kusmanov
Sergei Aleksandrovich Kusmanov
Igor SuminovIgor Suminov
Igor Suminov
PPPavel Podrabinnik
Pavel Podrabinnik
ROMAN KHMYROVROMAN KHMYROV
ROMAN KHMYROV
Sergey GrigorievSergey Grigoriev
Sergey Grigoriev
The paper considers the problem of increasing the wear resistance of steel products. For the first time, the technology of anodic plasma electrolytic sulfiding is proposed to increase the wear resistance of low-carbon steel. The composition, structure, and frictional properties of modified surface layers after sulfiding have been studied. The type and mechanism of wear are determined. The influence of the sliding speed of the sample over the counter body on the friction and wear resistance of the samples after processing is analyzed. The possibility of saturation of low-carbon steel with sulfur in an electrolyte with sulfur compounds is shown. The iron sulfide FeS in the surface layer is found. It has been established that the thickness of the sulfide zone and the relative amount of FeS in it have a positive effect on reducing the coefficient of friction and mass wear. The greatest decrease in the friction coefficient by 5.5 times and weight wear by 64 times occurs after sulfiding at 500 °C for 10 min. It was found that the mechanism of wear of sulfided samples is fatigue wear during dry friction and plastic contact.

1 September 2021 in Metals
Verified
Journal Article
Open access
PDF file
SSSvetlana Savushkina
Svetlana Savushkina
Aleksey Konstantinovich BuryakAleksey Konstantinovich Buryak
Aleksey Konstantinovich Buryak
AAAndrey Apelfeld
Andrey Apelfeld
Igor SuminovIgor Suminov
Igor Suminov
Coatings with thickness 40 to 150 μm were formed by plasma electrolytic oxidation (PEO) on the zirconium alloy Zr-1Nb (Zr-1% Nb) in the slurry electrolyte containing 9 g/L Na2SiO3 5H2O, 5 g/L Na(PH2O2) and 6 g/L submicron Y2O3 yttria powder during 60 min under the AC electrical mode at current densities 20; 30 and 40 A/dm2. The surface morphology, structure, composition, and corrosion-protective ability of the formed coatings have been analyzed. At PEO current density 30 A/dm2, a predominantly tetragonal phase of zirconia was formed in coatings. Increasing the PEO current density up to 40 A/dm2 promoted the formation of the coating surface layer containing submicron yttria particles. Electrochemical polarization studies in 0.5% LiOH solution showed that PEO coatings demonstrated high corrosion-protective ability. The dependence of the polarization currents on the PEO current density was found to be inconsequential.

9 August 2023 in Materials
Verified
Journal Article
Open access
PDF file
BKBoris Krit
Boris Krit
AAAndrey Apelfeld
Andrey Apelfeld
ABAnantoly Borisov
Anantoly Borisov
NMNatalia V. Morozova
Natalia V. Morozova
ARAlexander G. Rakoch
Alexander G. Rakoch
Sergey GrigorievSergey Grigoriev
Sergey Grigoriev
The review focuses on the surface modification of Zr and its alloys, which is necessary to expand the applications of these kinds of materials. Data on the properties of pure zirconium and its alloys are presented. Since surface engineering and the operation of the above materials are in most cases associated with the formation of oxide coatings, information on the characteristics of ZrO2 is given. In addition, attention is paid to phasing in the zirconium–oxygen system. It is noted that the most effective method of surface engineering of Zr and its alloys is plasma electrolytic modification (PEM) technology. Specific examples and modes of modification are described, and the reached results are analyzed. The relevance, novelty and originality of the review are determined by the insufficient knowledge about a number of practical features concerning the formation of functional oxide coatings on Zr and some of its alloys by the technology of PEM. In particular, the information on the phase composition and possibilities of stabilization of the tetragonal and cubic modifications of ZrO2, the effects of the component composition of electrolyte solutions and electrolyte suspensions, and the specifics of the treatment of additive shaping and deformed materials are rather contradictory. This review aims to collect recent advances and provide insights into the trends in the modification of Zr and its alloys, promote the formulation of practical recommendations and assess the development prospects.