Ilze Aulika

Dr. Ilze Aulika

orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2009 in Optics Express
Verified
Journal Article
Closed access
PDF file
Alexandr DejnekaAlexandr Dejneka
Alexandr Dejneka
IAIlze Aulika
Ilze Aulika
VTVladimir Trepakov
Vladimir Trepakov
JKJaromir Krepelka
Jaromir Krepelka
LJLubomir Jastrabik
Lubomir Jastrabik
ALAnna Lynnyk
Anna Lynnyk
The possibilities of in situ spectroscopic ellipsometry applied to phase transitions investigation in oxide thin films and crystals are examined in this work, along with the use of various parameters calculated from ellipsometric data (band gap energy Eg, refractive index n and surface roughness) together with the directly measured main ellipsometric angles ψ and Δ, for the detection of phase transitions. The efficiency of spectroscopic ellipsometry on “surface” phase transition and its sensitivity to surface defects are also demonstrated.

3 June 2022 in Vacuum
Verified
Journal Article
Closed access
MZMartins Zubkins
Martins Zubkins
IAIlze Aulika
Ilze Aulika
ESE. Strods
E. Strods
VVV. Vibornijs
V. Vibornijs
LBL. Bikse
L. Bikse
JPJuris Purans
Juris Purans

3 December 2020 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
MZMartins Zubkins
Martins Zubkins
JGJevgenijs Gabrusenoks
Jevgenijs Gabrusenoks
GCG. Chikvaidze
G. Chikvaidze
IAIlze Aulika
Ilze Aulika
JBJelena Butikova
Jelena Butikova
LBL. Bikse
L. Bikse
Crystalline wurtzite zinc oxide (w-ZnO) can be used as a wide bandgap semiconductor for light emitting devices and transparent or high temperature electronics. The use of amorphous zinc oxide (a-ZnO) can be an advantage in these applications. In this paper, we report on x-ray amorphous a-ZnOx thin films (∼500 nm) deposited at cryogenic temperatures by reactive magnetron sputtering. The substrates were cooled by a nitrogen flow through the copper substrate holder during the deposition. The films were characterized by x-ray diffraction, Raman, infrared, UV–Vis-near-infrared spectroscopies, and ellipsometry. The a-ZnOx films on glass and Ti substrates were obtained at the substrate holder temperature of approximately −100 °C. New vibration bands at 201, 372, and 473 cm−1 as well as O–H stretch and bend absorption bands in the a-ZnOx films were detected by Fourier transform infrared spectroscopy. Raman spectra showed characteristic ZnO2 peaks at 386 and 858 cm−1 attributed to the peroxide ion O22− stretching and libration modes, respectively. In addition, the films contain neutral and ionized O2 and O2− species. The a-ZnOx films are highly transparent in the visible light range (≈87%) and exhibit a refractive index of 1.68 at 2.25 eV (550 nm). An optical bandgap is 4.65 eV with an additional band edge absorption feature at 3.50 eV. It has been shown that the deposition on actively cooled substrates can be a suitable technique to obtain low temperature phases that cannot be deposited at room temperature.

31 December 2004 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
ASA. Sternberg
A. Sternberg
KKK. Kundzins
K. Kundzins
VZV. Zauls
V. Zauls
IAIlze Aulika
Ilze Aulika
LČL. Čakare
L. Čakare
YTY. Trushin
Y. Trushin

20 August 2024 in IEEE Sensors Journal
Verified
Journal Article
Open access
EBEmmanuel Bacher
Emmanuel Bacher
SESergio Cartiel Embid
Sergio Cartiel Embid
JGJorge Garcia-Pueyo
Jorge Garcia-Pueyo
JSJulija Stopar
Julija Stopar
AZAleš Zore
Aleš Zore
MLMartin Laurenzis
Martin Laurenzis
Light Detection and Ranging (LIDAR) sensors, employing direct Time-of-Flight (dTOF) measurements, are crucial for precise surface localization and are increasingly integrated into compact chip designs. These sensors have extensive use in proximity sensing in various applications. This paper presents the innovative use of LIDAR sensors for ranging within wave guides to accurately detect touch and pressure. In our OptoSkin sensors, light propagates via total internal reflection (TIR) within the wave guide. Then it is reflected back to the sensor as a result of wave guide deformation and/or scattering in the contact area, a phenomenon attributed to frustrated total internal reflection (FTIR). We have designed, simulated, and implemented different OptoSkin sensors using wave guides constructed from a flexible rod, rigid curved 3D printed resin, and planar soft silicone rubber, respectively. Each configuration is equipped with multiple LIDAR sensors, demonstrating effective localization of touch points. In addition, pressure sensing was performed on the elastic wave guides. These novel touch sensors show great potential for applications such as robotic sensor skins, which enhance tactile responsiveness and interaction.

8 September 2004 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
MKMaris Knite
Maris Knite
VTV. Teteris
V. Teteris
IAIlze Aulika
Ilze Aulika
HKH. Kabelka
H. Kabelka
AFA. Fuith
A. Fuith