The suitability of bamboo’s basic characteristics is very important for more specific purposes, such as composite raw materials. Anatomical, physical, mechanical, and chemical characteristics are some of bamboo’s fundamental characteristics. This study analyses the basic properties, such as physical, mechanical, and chemical properties of bamboo from the Forest Area with Special Purpose (FASP) Pondok Buluh Sumatera Island, Indonesia (I); analyses the relationship between the properties of each type of bamboo (II); and chooses the type of bamboo with the best properties that have the potential to be applied to composite materials, such as laminated bamboo (III). This study used materials consisting of six species of bamboo from the FASP Pondok Buluh. The manufacture of physical and mechanical test samples refers to the ISO 22157 standard, 2004, while the chemical properties test refers to the TAPPI 1999 standard. The chemical, physical, and mechanical properties of bamboo vary widely among species. The lowest holocellulose and α-cellulose content were found in the Kuning Bamboo (B. vulgaris var. vittata). The content of holocellulose and α-cellulose causes the lowest density in Kuning Bamboo (B. vulgaris var. vittata). The Dasar Bamboo (Bambusa vulgaris) has the highest levels of lignin. The substances have an impact on moisture content, T/R ratio, and shear strength. The Dasar Bamboo (Bambusa vulgaris) has the lowest moisture content, the highest T/R ratio, and the highest shear strength. However, Betung Bamboo (Dendrocalamus asper) has the highest density in this study. The compressive strength of the Betung Bamboo (Dendrocalamus asper) has the highest value. Therefore, Betung bamboo and Dasar Bamboo in this study were potentially utilized for composite materials, such as laminated bamboo.
The depletion of natural resources and increasing environmental apprehension regarding the reduction of harmful isocyanates employed in manufacturing polyurethanes (PUs) have generated significant attention from both industrial and academic sectors. This attention is focused on advancing bio-based non-isocyanate polyurethane (NIPU) resins as viable and sustainable substitutes, possessing satisfactory properties. This review presents a comprehensive analysis of the progress made in developing bio-based NIPU polymers for wood adhesive applications. The main aim of this paper is to conduct a comprehensive analysis of the latest advancements in the production of high-performance bio-based NIPU resins derived from lignin and tannin for wood composites. A comprehensive evaluation was conducted on scholarly publications retrieved from the Scopus database, encompassing the period from January 2010 to April 2023. In NIPU adhesive manufacturing, the exploration of substitute materials for isocyanates is imperative, due to their inherent toxicity, high cost, and limited availability. The process of demethylation and carbonation of lignin and tannin has the potential to produce polyphenolic compounds that possess hydroxyl and carbonyl functional groups. Bio-based NIPUs can be synthesized through the reaction involving diamine molecules. Previous studies have provided evidence indicating that NIPUs derived from lignin and tannin exhibit enhanced mechanical properties, decreased curing temperatures and shortened pressing durations, and are devoid of isocyanates. The characterization of NIPU adhesives based on lignin and tannin was conducted using various analytical techniques, including Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), matrix-assisted laser desorption/ionization with time-of-flight (MALDI-TOF) mass spectrometry, and gel permeation chromatography (GPC). The adhesive performance of tannin-based NIPU resins was shown to be superior to that of lignin-based NIPUs. This paper elucidates the potential of lignin and tannin as alternate sources for polyols in the manufacturing of NIPUs, specifically for their application as wood adhesives.
Oil palm plantations have expanded rapidly in Southeast Asia, particularly in Indonesia and Malaysia. A lot of products, including food and other edible products, oleo-chemicals, cosmetics, personal and household care, pharmaceutical products, and biodiesels are derived from palm oil, thus making them one of the most economically important plants. After 25–30 years of age, the palms are felled and replaced due to declining oil production. Oil palm trunks (OPT) are considered significant waste products. The trunks remain on the plantation site for nutrient recycling or burning. This increases insect and fungi populations causing environmental problems for the new palm generation or air pollution due to the fire. Up till now, OPT has received less attention in research studies. Therefore, this review summarizes the utilization of OPT into products made of oil palm fibers mainly derived from OPT and its application as the substitution of wood panel products. Some research works have been carried out on oil palm fibers that are derived from OPT for exploiting their potential as raw material of composite panel products, which is the objective of this review. Areas of development are processed into various conventional composite panel products such as plywood and laminated board which are usually predominantly made of wood and bonded by synthetic resins, particleboard with binder, or binderless and cement board which is arranged with wood as a minor component. All of the products have been presented and described technically according to best knowledge of the authors and literature review.
10 February 2021 in Wood Material Science & Engineering
The citric acid (CA)-based adhesive, as a new environment-friendly adhesive, has been developed and used for the manufacturing of plywood to resolve the problem of formaldehyde-based adhesive for human health. The effects of pressing time and temperature on physical and mechanical properties of plywood were examined. Three-layer plywood panels were bonded using CA adhesive with a 134 g/m2 of single glue spread on White jabon wood veneer. The plywood panels were hot-pressed at 5 MPa with three different pressing temperatures, 180°C, 190°C, 200°C, for 10 min, and also different pressing times, 4, 7, 10 min at 190°C. The physical and mechanical properties, such as moisture content, delamination, and shear strength, were evaluated according to JAS 233:2003. The results show that the plywood with pressing temperature of 190°C for 10 min had lower delamination and greater tensile shear strength than those of other plywood panels. Moreover, some properties of the plywood fulfilled the requirement of JAS 233:2003. Based on the FTIR analysis, citric acid plays an important role in the formation of ester linkages (R-COO-R) via esterification between carboxyl groups of citric acid and hydroxyl groups of White jabon wood veneer, resulting excellent properties of plywood.
3 March 2022 in Biomass Conversion and Biorefinery