Citric acid (CA) can be found naturally in fruits and vegetables, particularly citrus fruit. CA is widely used in many fields but its usage as a green modifying agent and binder for wood is barely addressed. Esterification is one of the most common chemical reactions applied in wood modification. CA contains three carboxyl groups, making it possible to attain at least two esterification reactions that are required for crosslinking when reacting with the hydroxyl groups of the cell wall polymers. In addition, the reaction could form ester linkages to bring adhesivity and good bonding characteristics, and therefore CA could be used as wood binder too. This paper presents a review concerning the usage of CA as a wood modifying agent and binder. For wood modification, the reaction mechanism between wood and CA and the pros and cons of using CA are discussed. CA and its combination with various reactants and their respective optimum parameters are also compiled in this paper. As for the major wood bonding component, the bonding mechanism and types of wood composites bonded with CA are presented. The best working conditions for the CA in the fabrication of wood-based panels are discussed. In addition, the environmental impacts and future outlook of CA-treated wood and bonded composite are also considered.

Natural rubber is of significant economic importance owing to its excellent resilience, elasticity, abrasion and impact resistance. Despite that, natural rubber has been identified with some drawbacks such as low modulus and strength and therefore opens up the opportunity for adding a reinforcing agent. Apart from the conventional fillers such as silica, carbon black and lignocellulosic fibers, nanocellulose is also one of the ideal candidates. Nanocellulose is a promising filler with many excellent properties such as renewability, biocompatibility, non-toxicity, reactive surface, low density, high specific surface area, high tensile and elastic modulus. However, it has some limitations in hydrophobicity, solubility and compatibility and therefore it is very difficult to achieve good dispersion and interfacial properties with the natural rubber matrix. Surface modification is often carried out to enhance the interfacial compatibilities between nanocellulose and natural rubber and to alleviate difficulties in dispersing them in polar solvents or polymers. This paper aims to highlight the different surface modification methods employed by several researchers in modifying nanocellulose and its reinforcement effects in the natural rubber matrix. The mechanism of the different surface medication methods has been discussed. The review also lists out the conventional filler that had been used as reinforcing agent for natural rubber. The challenges and future prospective has also been concluded in the last part of this review.

Nowadays, there is a significant trend away from solvent-based polyurethane systems towards waterborne polyurethane dispersions due to government regulations requiring manufacturers to lower total volatile organic compounds, as well as consumer preference for more environmentally friendly products. In this work, a renewable vegetable oil-based polyol derived from jatropha oil was polymerized with isophorone diisocyanate and dimethylol propionic acid to produce anionic waterborne polyurethane dispersion. Free standing films with up to 62 wt.% bio-based content were successfully produced after evaporation of water from the jatropha oil-based waterborne polyurethane (JPU) dispersion, which indicated good film formation. The chemical and thermo-mechanical properties of the JPU films were characterized. By increasing the OH numbers of polyol from 161 mgKOH/g to 217 mgKOH/g, the crosslinking density of the JPU was significantly increased, which lead to a better storage modulus and improved hydrophobicity. Overall, JPU produced from polyol having OH number of 217 mgKOH/g appears to be a promising product for application as a binder for wood and decorative coatings.

Mangrove ecosystems are crucial for biodiversity and coastal protection but face threats from climate change and human activities. This review assesses the productivity of the Matang Mangrove Forest Reserve (MMFR) in Malaysia, which is recognised as one of the best-managed mangrove forests, while also addressing challenges such as deforestation and climate change-induced factors. This review explores the concept of productivity in mangrove forests, highlighting their role in carbon sequestration and discussing litterfall measurements as fundamental metrics for assessing primary productivity. An analysis of historical changes in MMFR’s biomass and productivity revealed fluctuations influenced by logging, reforestation, and climatic conditions. Trends in MMFR productivity indicate a concerning decline attributed to anthropogenic activities such as aquaculture and industrial projects. A regression analysis conducted on Rhizophora apiculata data with age as the predictor and AGB as the response variable indicated a positive trend (slope = 3.61, R-squared = 0.686), suggesting a quantitative increase in AGB with age. Further analysis revealed a significant negative trend in MMFR’s overall productivity over years (coefficient = −3.974, p < 0.05) with a strong inverse relationship (rho = −0.818, p < 0.05), indicating declining AGB trends. Despite these challenges, this review underscores the significance of sustainable management practices, effective conservation efforts, and community engagement in maintaining mangrove ecosystem health and productivity. In conclusion, sharing management lessons from MMFR can contribute to global conservation and sustainable mangrove forest management efforts, fostering resilience in these vital ecosystems.