Leonardo Carvalho Mesquita

Prof. Dr. Leonardo Carvalho Mesquita

Civil Engineering, Universidade Federal de Viçosa, Viçosa, Brazil
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2024 in Buildings
Verified
Journal Article
Open access
PDF file
RMRoberta Prado Mendes
Roberta Prado Mendes
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita
MFMauricio de Pina Ferreira
Mauricio de Pina Ferreira
LTLeandro Mouta Trautwein
Leandro Mouta Trautwein
MARKSSUEL TEIXEIRA MARVILAMARKSSUEL TEIXEIRA MARVILA
MARKSSUEL TEIXEIRA MARVILA
MMMarília G. Marques
Marília G. Marques
In reinforced concrete flat slab buildings, the transference of unbalanced moments in the slab–column connections usually results from the asymmetry of spans, vertical loads, and horizontal forces from the wind. The punching strength of the slab–column connections can limit the load-carrying capacity of the structure in these cases, leading to structural collapse. The design code provisions are still based on empirical or semi-empirical equations; as the punching shear failure mechanisms are complex, and the ultimate strength is affected by several parameters. In this context, this paper presents the results of the computational investigation of the mechanical behaviour of flat slabs subjected to balanced and unbalanced moments using numerical Finite Element models. The numerical models were calibrated and accurately reproduced the behaviour and the punching resistance for concentric and eccentric loading. Furthermore, a parametric study was conducted to evaluate the mechanical behaviour of flat slabs under different load eccentricities, confirming that the increase in the unbalanced moment negatively impacts the load-carrying capacity of the slab–column connection. Furthermore, it was observed that all computational results obtained from models with unbalanced bending moments were higher than those estimated by the design codes.

28 November 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TRThiago Ranilson
Thiago Ranilson
LALuiz Arthur Silva de Aquino
Luiz Arthur Silva de Aquino
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita
MMMarília G. Marques
Marília G. Marques
AAAfonso Azevedo
Afonso Azevedo
MARKSSUEL TEIXEIRA MARVILAMARKSSUEL TEIXEIRA MARVILA
MARKSSUEL TEIXEIRA MARVILA
Recently, numerous studies have been carried out with natural fibers in cementitious composites, due to the viability of using this type of fiber as a substitute for synthetic fibers. In this field of study, the present research aims to evaluate the feasibility of using corn straw fiber for the production of innovative cementitious composites. Mortars with a composition of 1:1:6:1.55 (cement/lime/sand/water) containing 0, 2.5 and 5% corn straw fiber were produced. The corn straw fibers were treated with three different alkaline products: sodium hydroxide (NaOH), potassium hydroxide (KOH) and calcium hydroxide (Ca(OH)2). The compositions were evaluated by means of compressive strength, water absorption, density and porosity and consistency tests. Characterization tests were also carried out on the natural fibers subjected to the different treatments, where it was observed that chemical characterization revealed an increase in crystalline cellulose from 59.03% to 63.50% (NaOH), 62.41% (KOH) and 60.40% (Ca(OH)2), which enhances fiber strength. In the mortars, it was observed that the water absorption results were reduced when the alkaline treatments were used, reducing from 15.95% (composition without fibers) to 6.34% and 6.61% in the compositions with 2.5% and 5.0% of fibers treated with KOH, for example. The effects were also positive in the compositions with fibers treated in NaOH, where the water absorption values were 7.59% and 7.88% for the compositions containing 2.5% and 5.0% of treated fiber, respectively. Alkaline treatments also promote an increase in compressive strength when comparing the results of mortars with natural fibers and fibers treated with NaOH, for example. The result for mortars containing 5.0% untreated fibers was 0.22 MPa, while for the composition containing 5.0% fibers treated with NaOH, it was 3.79 MPa, an increase of more than 15x. This behavior is justified by the effect of the treatment, which, in addition to removing impurities from natural fibers, such as sugar, increases the crystalline cellulose content and the adhesion between fiber and matrix. Based on the results obtained, it is possible to conclude that (i) the treatment with NaOH increases the crystallinity and tensile strength of the fibers, promoting good properties for innovative cementitious composites; (ii) the treatment with KOH degrades the cellulose structure of the fiber, reducing the crystallinity and tensile strength; this promotes greater adhesion of the fiber to the matrix, reducing porosity and water absorption, but promotes a reduction in compressive strength when compared to composites with 2.5% natural fiber; and (iii) the treatment with Ca(OH)2 presents a reduction in water absorption and porosity, due to the impregnation of calcium in the fiber that improves the adhesion between fiber and matrix.

28 February 2023 in International Journal for Numerical and Analytical Methods in Geomechanics
Verified
Journal Article
Closed access
MPMatheus L. Peres
Matheus L. Peres
Elisa Dominguez SotelinoElisa Dominguez Sotelino
Elisa Dominguez Sotelino
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita

17 November 2022 in Applied Mathematical Modelling
Verified
Journal Article
Closed access
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita
Elisa Dominguez SotelinoElisa Dominguez Sotelino
Elisa Dominguez Sotelino
MPMatheus L. Peres
Matheus L. Peres

2 June 2023 in International Journal for Numerical and Analytical Methods in Geomechanics
Verified
Journal Article
Closed access
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita
Elisa Dominguez SotelinoElisa Dominguez Sotelino
Elisa Dominguez Sotelino
MPMatheus L. Peres
Matheus L. Peres
YLYves M. Leroy
Yves M. Leroy
1

10 November 2015 in REEC - Revista Eletrônica de Engenharia Civil
Verified
Journal Article
Open access
PDF file
Leonardo Carvalho MesquitaLeonardo Carvalho Mesquita
Leonardo Carvalho Mesquita
IAIzabel Christina D'Almeida Duarte de Azevedo
Izabel Christina D'Almeida Duarte de Azevedo
ECEduardo Souza Cândido
Eduardo Souza Cândido
GCGabriel Almeida Cathoud
Gabriel Almeida Cathoud
RESUMO: No Brasil, os resíduos de construção civil e demolição (RCD) chegam a atingir 60% da massa total de resíduos sólidos urbanos (RSU) produzidos, com geração per capita em torno de 500 kg/(hab. ano). O objetivo desse trabalho foi analisar a viabilidade técnica da utilização de agregados produzidos pela britagem de RCD em substituição aos materiais convencionais (areia, seixo, pedra britada e pó de pedra) na produção de blocos vazados de concreto simples para alvenaria de vedação. O agregado reciclado foi caracterizado e, a partir de um traço padrão utilizado por uma empresa de pré-moldados, foram produzidos cinco novos traços de concreto em que se variou a relação entre os agregados naturais (areia artificial e areia lavada) e os agregados de RCD. Os blocos produzidos foram levados à ruptura aos 28 dias, tendo apresentado valores de resistência característica à compressão entre 2,5 MPa (com adição de areia e sem RCD) e 4,3 MPa (com RCD e sem a adição de areia), superiores ao estabelecido em norma. Conclui-se que a utilização de agregados reciclados de RCD é uma alternativa viável para substituir a brita convencional na produção de blocos vazados de vedação, contribuindo para minimizar o passivo ambiental, dando um destino adequado para os RCD e, principalmente, reduzindo a extração de agregados naturais. In Brazil, construction and demolition waste (CDW) reach up to 60% of the total mass of solid waste (MSW) produced, with per capita generation of approximately 500 kg/(inhabitant.year). The objective of this paper is to analyze the technical feasibility of using recycled CDW aggregates replacing the conventional materials (sand, pebble, crushed stone and stone dust) in the production of concrete sealing blocks. The recycled aggregate was characterized and, from a trace pattern used by the partner company five new concrete mixtures were produced considering different ratios between natural aggregates (sand) and recycled CDW. The blocks produced were tested and brought to rupture after 28 days. Compression characteristic values of 2.5 MPa (with sand and without recycled CDW aggregates) and 4.3 MPa (with recycled CDW aggregates and without sand) were observed. These values are above the minimum value set in Brazilian standards. The results lead to the conclusion that recycled RCD aggregates are an alternative to replace conventional gravel in the production of concrete sealing blocks, helping to minimize environmental liabilities, giving a suitable destination to the residues and, especially, reducing the extraction of natural aggregates.